Journals / European Mechanical Science / 2022 / Cilt: 6 - Sayı: 1

Evaluation of fracture toughness and Charpy V-notch test correlations for selected Al alloys

Pages
1–8
Publication Date
2022-10-12
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Lastly, the ductile fracture of the 6061-T6 Al alloy tensile test specimens executed at the quasi-static conditions was attributed to having a higher fracture toughness.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This research experimentally compared the correlations on the fracture toughness using Charpy V-notch tests.
📊
Key Findings & Data:For the current work, nine different fracture toughness correlations were selected using the existing literature and most common Al alloys, including 2024-T4, 6061-T6, and 7075-T6, were chosen as testing materials..
💡
Conclusion & Impact:Lastly, the ductile fracture of the 6061-T6 Al alloy tensile test specimens executed at the quasi-static conditions was attributed to having a higher fracture toughness.
🔬Design:Research Article
📍Scope:2024 Verileri
⚙️Variables:Fracture Toughness · Charpy V-notch test · Deformation Behavior

Abstract

This research experimentally compared the correlations on the fracture toughness using Charpy V-notch tests. The fracture toughness tests are expensive, complex, and unreliable. Therefore, researchers developed correlations using Charpy V-notch tests to estimate fracture toughness, thereby structural integrity assessment. For the current work, nine different fracture toughness correlations were selected using the existing literature and most common Al alloys, including 2024-T4, 6061-T6, and 7075-T6, were chosen as testing materials.. Tensile tests were utilized to determine the deformation behavior of the tested alloys. Also, Charpy V-notch tests were carried out to obtain absorbed energy during the low impact conditions. Rupture strain, yield, and ultimate tensile strengths of the alloys were determined by tensile testing. Charpy V-notch test results revealed that the energy absorption ability of the 6061-T6 Al alloy is roughly two times higher than the 2024-T4 and roughly four times higher than the 7075-T6 Al alloy. The fracture toughness estimations resulted in a broad range of values in which the highest and lowest values were obtained when the equations of Li et al. and Roberts and Newton were employed, respectively. The experimentally obtained fracture toughness values attained from the literature were used to define the error of each correlation. The correlation developed by Lucan et al. yielded the lowest average error with an error percentage of 15.6%. Lastly, the ductile fracture of the 6061-T6 Al alloy tensile test specimens executed at the quasi-static conditions was attributed to having a higher fracture toughness.

🔖

Cite This Article

YILDIZ, R. A. (2022). Evaluation of fracture toughness and Charpy V-notch test correlations for selected Al alloys. European Mechanical Science, Cilt: 6 - Sayı: 1, 1–8. https://ajindex.com/articles/512386

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Smith, R.J., Horn, A.J., Sherry, A.H., (2018). Relating Charpy energy to fracture toughness in the lower transition region using a Weibull stress dependent energy scaling model. International Journal of Pressure Vessels and Piping. 166: 72–83. doi: 10.1016/j.ijpvp.2018.06.001
  2. Anderson, T.L., (2005). Fracture Mechanics. Boca Raton: CRC Press Taylor & Francis Group. [3] (2020). Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials. West Conshohocken, PA
  3. Ritchie, R.O., Knott, J.F., Rice, J.R., (1973). On the relationship between critical tensile stress and fracture toughness in mild steel. Journal of the Mechanics and Physics of Solids. 21(6): 395–410. doi: 10.1016/0022-5096(73)90008-2
  4. Rossoll, A., Berdin, C., Prioul, C., (2002). Determination of the fracture toughness of a low alloy steel by the instrumented charpy impact test. International Journal of Fracture. 115(3): 205–26. doi: 10.1023/A:1016323522441
  5. Schindler, H.J., Morf, U., (1993). A closer look at estimation of fracture toughness from Charpy V-notch tests. International Journal of Pressure Vessels and Piping. 55(2): 203–12. doi: 10.1016/0308-0161(93)90028-R
  6. A Salemi Golezani., (2013). The Effect of Microstructure on Estimation of the Fracture Toughness (KIC) Rotor Steel Using Charpy Absorbed Energy (CVN). Journal of Advanced Materials and Processing. 1(3): 11–7
  7. Terán, G., Capula-Colindres, S., Angeles-Herrera, D., Velázquez, J.C., Fernández-Cueto, M.J., (2016). Estimation of fracture toughness KIC from Charpy impact test data in T-welded connections repaired by grinding and wet welding. Engineering Fracture Mechanics. 153(January 2018): 351–9. doi: 10.1016/j.engfracmech.2015.12.010
  8. Takashima, Y., Ito, Y., Lu, F., Minami, F., (2019). Fracture toughness evaluation for dissimilar steel joints by Charpy impact test. Welding in the World. 63(5): 1243–54. doi: 10.1007/s40194-019-00752-x
  9. Bianchi, K.E., Barbosa, V.S., Savioli, R., Fernandes, P.E.A., Ruggieri, C., (2017). Correlation of Fracture Toughness With Charpy Impact Energy for Low Alloy, Structural Steel Welds. Volume 6B: Materials and Fabrication, American Society of Mechanical Engineers p. 1–11
  10. Zhou, Z., Huang, S., Hui, H., Zhang, Y., (2020). Estimation of Minimum Design Metal Temperature by MDMT Curve and Correlations of Charpy Impact and Fracture Toughness. Journal of Pressure Vessel Technology. 142(6). doi: 10.1115/1.4046888
  11. Puppala, G., Moitra, A.,