SavedAdd your journal

Journals / Ege Üniversitesi Diş Hekimliği Fakültesi / 2021 / Cilt: 42 - Sayı: 1

Color Stability and Translucency of Two CAD-CAMRestorative Materials Subjected To Mechanical Polishing,Staining, and Prophylactic Paste Polishing Procedures

Mekanik Cilalama, Renklenme ve Profilaktik Cilalama Sonrası BDT/BDÜ Materyallerinin Renk Değişimi ve Translusensi Değerlerinin İncelenmesi

Duygu RECEN
Bengisu YILDIRIM
Pages
1–8
Publication Date
2022-10-11
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Results: For baseline measurements and after mechanic polishing measurement, the mean translucency value of the Cerasmartwas significantly higher than Initial-LRF (p

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Introduction: The aim of this study is to evaluate the translucency and color change of two computer-aided design and computer aided manufacturing (CAD/CAM) blocks after subjected to mechanic polishing, coffee staining, and prophylactic paste polishing procedures.
📊
Key Findings & Data:Methods: 26 specimens (n=13) were obtained from each CAD/CAM block (Cerasmart A2-HT; GC, Initial-LRF, A2-HT: GC).
💡
Conclusion & Impact:Results: For baseline measurements and after mechanic polishing measurement, the mean translucency value of the Cerasmartwas significantly higher than Initial-LRF (p
🔬Design:Research Article
📍Scope:26 specimens
⚙️Variables:Domain Parameters

Abstract

Introduction: The aim of this study is to evaluate the translucency and color change of two computer-aided design and computer aided manufacturing (CAD/CAM) blocks after subjected to mechanic polishing, coffee staining, and prophylactic paste polishing procedures. Methods: 26 specimens (n=13) were obtained from each CAD/CAM block (Cerasmart A2-HT; GC, Initial-LRF, A2-HT: GC). Colorchange values were evaluated after subjected to mechanic polishing, coffee staining, and prophylactic polishing procedures. Datawere analyzed by a Shapiro-Wilk normality test and the translucency and color change values were evaluated statistically withFriedman test. Mann Whitney-U test was used to determine the statistical significance between the Cerasmart and Initial-LRF interms of translucency and color change (α=.05). Results: For baseline measurements and after mechanic polishing measurement, the mean translucency value of the Cerasmartwas significantly higher than Initial-LRF (p

Özet

Giriş ve Amaç: Bu çalışmanın amacı, mekanik polisaj, kahve ile renklendirme ve profilaktik polisaj prosedürlerine tabi tutulduktansonra bilgisayar destekli tasarım ve bilgisayar destekli (BDT/BDÜ) bloklardan elde edilen örneklerin translusensi ve renk değişiminideğerlendirmektir. Yöntem ve Gereçler: Her iki bloktan (Cerasmart A2-HT; GC, Initial-LRF, A2-HT: GC) toplam 26 adet örnek (n= 13) elde edildi.Örneklerin renk değişimi ve translusensi değerleri mekanik cilalama, kahve ile renklendirme ve profilaktik cilalama prosedürlerinetabi tutulduktan sonra spektrofotometre ile ölçüldü. Veriler Shapiro-Wilk normallik testi ile analiz edildi. Translusensi ve renk değişimdeğerleri Friedman testi ile istatistiksel olarak değerlendirildi. Translusensi ve renk değişimi açısından Cerasmart ve Initial-LRFarasındaki istatistiksel farkı belirlemek için ise Mann Whitney-U testi kullanıldı (α=.05). Bulgular: Cerasmart ilk ölçümde ve mekanik parlatma sonrası Initial-LRF’e göre istatiksel olarak anlamlı derecede daha translusentbulunmuştur (p

🔖

Cite This Article

RECEN, D., YILDIRIM, B. (2022). Color Stability and Translucency of Two CAD-CAMRestorative Materials Subjected To Mechanical Polishing,Staining, and Prophylactic Paste Polishing Procedures. Ege Üniversitesi Diş Hekimliği Fakültesi, Cilt: 42 - Sayı: 1, 1–8. https://ajindex.com/articles/496273

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Yu B, Ahn J-S and Lee Y-K. Measurement of translucency of tooth enamel and dentin. Acta Odontol Scand 2009;67:57-64. 2. https://europe.gc.dental/en-GB (2020, accessed 12 October, 2020)
  2. Barutçugil Ç, Bilgili D, Barutcigil K, et al. Discoloration and translucency changes of CADCAM materials after exposure to beverages. J Prosthet Dent 2019;122:325-331
  3. Aladag A, Oguz D, Çömlekoglu ME, Akan E. In vivo wear determination of novel CAD/CAM ceramic crowns by using 3D alignment. J Adv Prothodont 2019;11:120-127
  4. Awada A and Nathanson D. Mechanical properties of resin-ceramic CAD-CAM restorative materials. J Prosthet Dent 2015;114:587-593
  5. Acar O, Yilmaz B, Altintas SH, et al. Color stainability of CAD-CAM and nanocomposite resin materials. J Prosthet Dent 2016;115:71-75
  6. Lauvahutanon S, Shiozawa M, Takahashi H, et al. Discoloration of various CAD-CAM blocks after immersion in coffee. Restor Dent Endod 2017;42:9- 18
  7. Abu-Obaid A, AlMawash A, Alyabis N, et al. An in vitro evaluation of the effect of polishing on the stainability of different CAD-CAM ceramic materials. Saudi Dent J 2019;32:135-141
  8. Sarikaya I, Yerliyurt K and Hayran Y. Effect of surface finishing on the colour stability and translucency of dental ceramics. BMC Oral Health 2018;18:40
  9. Sagsoz O and Sagsoz NP. Chemical degradation of dental CAD-CAM materials. Biomed Mater Eng 2019;30:419-426
  10. Liebermann A, Spintzyk S, Reymus M, et al. Nine prophylactic polishing pastes: impact on discoloration, gloss, and surface properties of a CAD-CAM resin composite. Clin Oral Investig 2019;23:327-335
  11. Commission Internationale de l’Eclairage (CIE). CIE technical report: colorimetry. [CIE Pub No.15.3]. 2004
  12. Johnston WM. Review of translucency determinations and applications to dental materials. JERD 2014;26:217-223
  13. Yildirim B, Recen D, Tekeli Simsek A. Effect of cement color and tooth‐shaded background on the final color of lithium disilicate and zirconia‐ reinforced lithium silicate ceramics: An in vitro study. JERD 2020. (Epub ahead of the print
  14. Chu FC, Chow TW and Chai J. Contrast ratios and masking ability of three types of ceramic veneers. J Prosthet Dent 2007;98:359-364
  15. Tekce N, Tuncer S, Demirci M, et al. The effect of different drinks on the color stability of different restorative materials after one month. Restor Dent Endod 2015;40:255-261
  16. Koroglu A, Sahin O, Dede DO, et al. Effect of different surface treatment methods on the surface roughness