SavedAdd your journal

Journals / Düzce Üniversitesi Bilim ve Teknoloji Dergisi / 2020 / Cilt: 8 - Sayı: 1

Investigation of PVD TiAlN+Al203 and CVD TiCN+TiN Coating Performance in AISI T15 Steel Processing

AISI T15 Çeliğinin İşlenmesinde PVD TiAlN + Al203 ve CVD TiCN+TiN Kaplama Performansının Araştırılması

İsmail TEKAÜT
Pages
1084–1094
Publication Date
2022-10-12
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

This situation is interpreted to the properties of the coating material of the cutting tools.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, AISI T15 high speed steel with high abrasion resistance of 45 HRC was turned into TiCN+TiN coated carbide cutting tools with TiAlN+Al203 and CVD method by PVD method.
📊
Key Findings & Data:Experiments that kept constant the cutting depth (1.5 mm) was conducted combination of four different cutting speeds (60, 80, 140 and 200 m / min) and three different feed rates (0.1, 0.3 and 0.6 mm / rev).
💡
Conclusion & Impact:This situation is interpreted to the properties of the coating material of the cutting tools.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Tornalama · PVD TiAlN+ Al203 · CVD Ti (CN)

Abstract

In this study, AISI T15 high speed steel with high abrasion resistance of 45 HRC was turned into TiCN+TiN coated carbide cutting tools with TiAlN+Al203 and CVD method by PVD method. Experiments that kept constant the cutting depth (1.5 mm) was conducted combination of four different cutting speeds (60, 80, 140 and 200 m / min) and three different feed rates (0.1, 0.3 and 0.6 mm / rev). In this study, the effect of cutting parameters and coating type on surface roughness was investigated. PVD TiAlN+Al203 coated cutting tools were performed better than CVD TiCN+TiN coated cutting tools in low feed rate (0.1mm / rev). But, when the amount of progression was 0.6 mm / rev, CVD TiCN+TiN coated cutting tools were performed better than PVD TiAlN+Al203 coated cutting tools coated cutting tools in low feed rate (0.1mm / rev). This situation is interpreted to the properties of the coating material of the cutting tools.

Özet

Bu çalışmada, 45 HRC sertliğinde aşınma dayanımı yüksek olan AISI T15 yüksek hız çeliği, PVD yöntemiyle TiAlN+Al203 ve CVD yöntemiyle TiCN+TiN kaplanmış karbür kesici takımlarla tornalanmıştır. Kesme derinliğinin (1,5 mm) sabit tutulduğu deneyler, dört farklı kesme hızı (60, 80, 140 ve 200 m/dak) ile üç farklı ilerleme miktarı (0,1, 0,3 ve 0,6 mm/dev) kombinasyonlarında gerçekleştirilmiştir. Çalışmada kesme parametreleri ve kaplama türünün yüzey pürüzlülüğüne etkisi araştırılmıştır. Düşük ilerleme miktarında (0,1mm/dev) PVD TiAlN+Al203 kaplamalı kesici takımlar CVD TiCN+TiN kaplamalı kesici takımlardan daha iyi performans sergilemiştir. Fakat ilerleme miktarının 0,6 mm/dev olduğunda, CVD TiCN+TiN kaplamalı kesici takımlar PVD TiAlN+Al203 kaplamalı kesici takımlardan daha iyi performans sergilemişlerdir. Bu durumun kesici takımların kaplama malzemesinin özelliklerine yorumlanmıştır.

🔖

Cite This Article

TEKAÜT, İ. (2022). Investigation of PVD TiAlN+Al203 and CVD TiCN+TiN Coating Performance in AISI T15 Steel Processing. Düzce Üniversitesi Bilim ve Teknoloji Dergisi, Cilt: 8 - Sayı: 1, 1084–1094. https://ajindex.com/articles/494255

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. M. Tayanç ve G. Zeyti, “Yüksek Hız Çeliklerinin İç Yapı Ve Işıl İşlem Özellikleri,” BA.Ü. Fen Bilimleri Enstitüsü Dergisi, c. 2, s. 1, ss. 103-122, 2000
  2. Ö. Tekaslan, N. Gerger ve U. Şeker, “Cnc Torna Tezgahında AISI 304 Çeliklerin İşlenemesinde Optimum Yüzey Pürüzlülüğünü Sağlayacak Kesme Parametrelerinin Tespiti,” Dumlupınar Üniversitesi Fen Bilimleri Enstitüsü Dergisi, s. 16, 2008
  3. M. Bilgin ve H. B. Ulaş, “Islah Çeliğinin Farkli Kesici Takimlarla İşlenmesinde Kesme Parametrelerinin Talaş Şekilleri Üzerine Etkisi Ve Talaş Şekillerinin Sınıflandırılması,” Akademik Platform- ISITES, Valencia, Spain, 2015 ss. 1308-1317
  4. F. Kara, K. Aslantaş ve A. Çiçek, “Ortagonal Kesme Işleminde Kaplama Malzemesinin Talaş Morfolojisi Üzerinde Etkisinin Araştırılması,
  5. Ulusal Tasarım İmalat ve Analiz Kongresi, Balıkesir, Türkiye, 2010
  6. M. Boy, İ. Çiftçi, M. Günay, F. Özhan,” Application of the Taguchi Method to Optimize the Cutting Conditions in Hard Turning of A Ring Bore”, Materials and Technology, c 49, s 5, ss 765–772, 2015
  7. M. A. El Hakim, M. A. Shalaby, S. C. Veldhuis and G. K. Dosbaeva, “Effect of secondary hardening on cutting forces, cutting temperature, and tool wear in hard turning of high alloy tool steels,” Measurement, c. 65, ss. 233-238, 2015
  8. A. Hosokawa, G. Hoshino, T. Koyano, T. Ueda, “Cutting characteristics of PVD-coated tools deposited by filtered arc deposition (FAD) method,” CIRP Annals, c. 67, s. 1, ss. 83–86, 2018
  9. M. Pellizzari, “High temperature wear and friction behaviour of nitrided, PVD-duplex and CVD coated tool steel against 6082 Al alloy,” Wear, c. 271, s. 9-10, ss. 2089– 2099,2011
  10. M. Nilsson, M. Olsson, “Tribological testing of some potential PVD and CVD coatings for steel wire drawing dies,” Wear, c. 273, ss. 55– 59, 2011
  11. S. Saketi, M. Olsson,” Influence of CVD and PVD coating micro topography on the initial material transfer of 316L stainless steel in sliding contacts – A laboratory study,” Wear, c. 388, ss. 29–38, 2017
  12. A. Naskar, A. K. Chattopadhyay,” Investigation on flank wear mechanism of CVD and PVD hard coatings in high speed dry turning of low and high carbon steel,” Wear, c. 396–397, ss. 98–106, 2018
  13. D. Boing, A. J. Oliveira, R. B. Schroeter,” Limiting conditions for application of PVD (TiAlN) and CVD (TiCN/Al2O3/ TiN) coated cemented carbide grades in the turning of hardened steels,” Wear, c. 416–417, ss. 54–61, 2018
  14. S. Koseki, K. Inoue, K. Sekiya, S. Morito, T. Oh