Journals / Çukurova Üniversitesi Mühendislik Fakültesi dergisi / 2022 / Cilt: 37 - Sayı: 2

An Investigation on Dimensional Accuracy of 3D Printed PLA, PET-G and ABS Samples with Different Layer Heights

Üç Boyutlu Baskı ile Farklı Katman Yüksekliklerinde Üretilmiş PLA, PET-G ve ABS Parçaların Boyutsal Doğruluğu Üzerine Bir Araştırma

Pages
449–458
Publication Date
2022-10-12
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Furthermore, the best surface quality was attained in PLA samples compared to other filaments.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the effect of filament type and layer height on the dimensional accuracy of the 3D printed tensile test samples from PLA, PET-G, and ABS was investigated in depth.
📊
Key Findings & Data:Based on the fused filament fabrication (FFF) technology, tensile test samples were produced with various layer heights (0.2 mm, 0.3 mm, and 0.4 mm) while the other printing parameters were kept constant, except for nozzle and building platform temperature.
💡
Conclusion & Impact:Furthermore, the best surface quality was attained in PLA samples compared to other filaments.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Boyutsal doğruluk · Eriyik filament üretimi · PLA

Abstract

In this study, the effect of filament type and layer height on the dimensional accuracy of the 3D printed tensile test samples from PLA, PET-G, and ABS was investigated in depth. Based on the fused filament fabrication (FFF) technology, tensile test samples were produced with various layer heights (0.2 mm, 0.3 mm, and 0.4 mm) while the other printing parameters were kept constant, except for nozzle and building platform temperature. Length, width, and height values of the produced test samples were measured, and obtained results were compared with design dimensions to observe the dimensional accuracy of each sample. Also, surface roughness measurements were performed on the samples to examine their final surface quality. From dimensional measurements, it was seen that the most accurate results were recorded for PET-G (in length and height) and PLA (in width) samples. Furthermore, the best surface quality was attained in PLA samples compared to other filaments.

Özet

Bu çalışmada, PLA, PET-G ve ABS'den 3D baskılı çekme testi numunelerinin boyutsal doğruluğuna filament tipi ve katman yüksekliğinin etkisi derinlemesine araştırılmıştır. Eriyik filament üretimi teknolojisine dayalı olarak, çeşitli katman yüksekliklerinde (0,2 mm, 0,3 mm ve 0,4 mm) çekme test numuneleri üretilirken, meme ve bina platform sıcaklığı dışındaki diğer parametreler sabit tutulmuştur. Üretilen test numunelerinin uzunluk, genişlik ve yükseklik değerleri ölçülerek, elde edilen sonuçlar tasarım boyutları ile karşılaştırılarak her bir numunenin boyutsal doğruluğu gözlemlenmiştir. Ayrıca, nihai yüzey kalitelerini incelemek için numuneler üzerinde yüzey pürüzlülük ölçümleri yapılmıştır. Boyutsal ölçümlerden en doğru sonuçların PET-G (uzunlukta ve yükseklikte) ve PLA (genişlikte) numuneleri için kaydedildiği görüldü. Ayrıca PLA numunelerinde diğer filamentlere kıyasla en iyi yüzey kalitesi elde edilmiştir.

🔖

Cite This Article

BOLAT, Ç., ERGENE, B. (2022). An Investigation on Dimensional Accuracy of 3D Printed PLA, PET-G and ABS Samples with Different Layer Heights. Çukurova Üniversitesi Mühendislik Fakültesi dergisi, Cilt: 37 - Sayı: 2, 449–458. https://ajindex.com/articles/485070

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Demir, H., Gündüz, S., 2009. The Effects of Aging on Machinability of 6061 Aluminum Alloy. Materials and Design, 30(5), 1480–1483
  2. Ghosh, S., Kain, V., 2010. Microstructural Changes in AISI 304L Stainless Steel Due to Surface Machining: Effect on Its Susceptibility to Chloride Stress Corrosion Cracking. Journal of Nuclear Materials, 403(1-3), 62-67
  3. Yang, J., Yang, W., Chen, W., Tao, X., 2020. An Elegant Coupling: Freeze-casting and Versatile Polymer Composites. Progress in Polymer Science, 109, 101289
  4. Attia, U.M., Marson, S., Alcock, J.R., 2009. Micro-injection Moulding of Polymer Microfluidic Devices. Microfluids and Nanofluids, 7
  5. Bolat, Ç., Akgün, İ.C., Göksenli, A., 2020. On the Way to Real Applications: Aluminum Matrix Syntactic Foams. European Mechanical Science, 4(3), 131-141
  6. Ergene, B., Bolat, Ç., 2019. A Review on the Recent Investigation Trends in Abrasive Waterjet Cutting and Turning of Hybrid Composites. Sigma Journal of Engineering and Natural Sciences, 37(3), 989-1016
  7. Yalçın, B., Ergene, B., 2018. Analyzing the Effect of Crack in Different Hybrid Composite Materials on Mechanical Behaviors. Pamukkale University Journal of Engineering Sciences, 24(4), 616-625
  8. Novák, P., 2020. Advanced Powder Metallurgy Technologies. Materials, 13, 1742
  9. Ergene, B., 2022. Simulation of the Production of Inconel 718 and Ti6Al4V Biomedical Parts with Different Relative Densities by Selective Laser Melting (SLM) Method. Journal of the Faculty of Engineering and Architecture of Gazi University, 37(1), 469-484
  10. Ergene, B., Şekeroğlu, İ., Bolat, Ç., Yalçın, B., 2021. An Experimental Investigation on Mechanical Performances of 3D Printed Lightweight ABS Pipes with Different Cellular Wall Thickness. Journal of Mechanical Engineering and Sciences, 15(4), 8169-8177
  11. Kamer, M.S., Doğan, O., Temiz, Ş., Yaykaşlı, H., 2021. Investigation of the Mechanical Properties of Flexural Test Samples Produced Using Different Printing Parameters with a 3D Printer. Çukurova University Journal of the Faculty of Engineering, 36(3), 835-846
  12. Kumar, P., Ahuja, I.P.S., Singh, R., 2012. Application of Fusion Deposition Modelling for Rapid Investment Casting- A Review. International Journal of Materials Engineering Innovation, 3(1), 204-227
  13. Ingole, D.S., Kuthe, A.M., Thakare, S.B., Talankar, A.S., 2009. Rapid Prototyping- A Technology Transfer Approach for Development of Rapid Tooling. Rapid Prototyping Journal, 15(1), 280-290
  14. Venkataraman,