Journals / Çimento ve Beton Dünyası / 2003 / Cilt: 7 - Sayı: 41

Influence of size and types of aggregate on the interfacial bond strength

Agrega cinsi ve tane boyunun arayüzey aderans dayanımına etkisi

Pages
65–77
Publication Date
2022-10-11
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It was found that the interfacial bond strength increases as the aggregate size reduces irrespective of the type of aggregate and mortar matrix and that sandstone aggregates yield higher interfacial bond strength than the granite aggregates for all mortar types.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The paper reports on a study of the interface between two types of cylindrical aggregates (sandstone and granite) having four different diameters (10,14, 20 and 30mm) and three types of mortar matrices (plain, 10% silica fume (SF) and 20% SF mortar).
📊
Key Findings & Data:Interfacial strength was then compared on the basis of aggregate size and type, and it was related to the amount of silica ($Si0_2$)in the interface.
💡
Conclusion & Impact:It was found that the interfacial bond strength increases as the aggregate size reduces irrespective of the type of aggregate and mortar matrix and that sandstone aggregates yield higher interfacial bond strength than the granite aggregates for all mortar types.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

The paper reports on a study of the interface between two types of cylindrical aggregates (sandstone and granite) having four different diameters (10,14, 20 and 30mm) and three types of mortar matrices (plain, 10% silica fume (SF) and 20% SF mortar). The strength of the interface was determined experimentally using aggregate push-out method and chemical analyses were conducted by means of scanning electron microscopy (SEM) and energy dispersive x-ray (EDX) analyser. Interfacial strength was then compared on the basis of aggregate size and type, and it was related to the amount of silica ($Si0_2$)in the interface. It was found that the interfacial bond strength increases as the aggregate size reduces irrespective of the type of aggregate and mortar matrix and that sandstone aggregates yield higher interfacial bond strength than the granite aggregates for all mortar types. It was also found that the higher the$Si0_2$concentration in the interface, the higher the interfacial bond strength due to the densification role of SF for all aggregate and mortar types.

Özet

Bu makale, dört farklı çaptaki (10, 14, 20 ve 30 mm) iki ayrı cins silindirik agreganın (kumlası ve granit) ve üç ayrı tipteki harç matrisinin (sade, %10 silis dumanı (SD) ve %20 SD içeren harçlar) arayüzeyiyle ilgili bîr çalışmayı anlatmaktadır. Arayüzey dayanımı, deneysel olarak agrega itme metodu ile ve kimyasal analiz, taramalı elektron mikroskop (TEM) enerji yayan x-ray analiz cihazlarıyla (EYX) yapıldı. Daha sonra arayüzey dayanımı agraga tip ve boyuna göre karşılaştırıldı ve bu arayüzeydeki silis ($Si0_2$) ile ilgiliydi. Arayüzey aderans dayanımının agrega cinsinden ve harç matrisinden bağımsız olarak agrega boyu küçüldükçe arttığı ve bütün harçlarda kumtaşı agregalarının granit agregalarından daha yüksek arayüzey aderans dayanımı verdiği görüldü. Ayrıca arayüzeydeki $Si0_2$ konsantrasyonu arttıkça bütün agraga ve harç tiplerinde SD' nin yoğunlaşmasına bağlı olarak arayüzey aderans dayanımının arttığı da görüldü.

🔖

Cite This Article

ÇALIŞKAN, S. (2022). Influence of size and types of aggregate on the interfacial bond strength. Çimento ve Beton Dünyası, Cilt: 7 - Sayı: 41, 65–77. https://ajindex.com/articles/483488

References (2)

  1. Neville, A. M. Properties of Concrete, Forth Edition,
  2. Longman, London, 1995, pp. 844 2.Lee, K. M„ Buyukozturk, 0., and Oumera, A., Fracture Analysis of Mortar-Aggregate Interfaces in Concrete, Journal of Engineering Mechanics, Vol. 118, No. 10,1992, pp. 2031 - 2047 3.Bentz, D. P., Stutzman, P. E., And Garboczi, E. J., Experimental and Simulation Studies of the Interfacial Zone in Concrete, Cement and Concrete Research, Vol. 22,1992, pp. 891-902 4.Buyukozturk, 0. and Lee, K. M., Interface Fracture Mechanics of Concrete Composites, Proceedings of the First Conference on Fracture Mechanics of Concrete structures (FraMCoSI), Ed. Z. P. Bazant, Colorado, 1992, pp. 163-168 5.van Mier, J. G. M„ Fracture Processes of Concrete: Assessment of Material Parameters for Fracture Models, CRC Press, London, 1997, pp.448 6.Monteiro, P. J. M. and Andrade, W. P., Analysis of the Rock-Cement Paste Bond Using Probabilistic Treatment of Brittle Strength, Cement and Concrete Research, Vol. 17,1987, pp. 919 - 926 7.Zhang, M. and Gjorv, 0. E., Microstructure of the Interfacial Zone between Lightweight Aggregate and Cement Paste, Cement and Concrete Research, Vol. 20,1990, pp. 610 - 618 8.Bentz, D. P;, And Garboczi, E. J., Simulation Studies of the Effects of Mineral Admixtures on the Cement Paste-Aggregate Interfacial Zone, ÂÇI.Materials Journal, V. 88, No. 5,1991, pp. 518-529 9.Tschegg, E. K„ Rotter, H. M., Roelfstra, P.E., Bourgund, U. and Jussel, P., Fracture Mechanical Behaviour of Aggregate-Cement Matrix Interfaces, Journal of Materials in Civil Engineering, Vol. 7, No. 4,1995, pp. 199 - 203 10.Caliskan, S., B. L. Karihaloo and B. I. G. Barr, Study of Rock Mortar Interfaces. Part I: Surface Roughness of Rock Aggregates and Microstructural Characteristics of Interface, Magazine of Concrete Research, Vol. 54, No. 6, December 2002, pp. 449 - 461 11.Caliskan, S., Karihaloo, B. L. and Barr, B. I. G., Study of Rock Mortar Interfaces. Part II: Strength of Interface, Magazine of Concrete Research, Vol. 54, No. 6, December 2002, pp. 463 - 472 12.Caliskan, S. and B. L. Karihaloo Influence of Silica Fume on the Aggregate / Mortar Interfacial Bond Strength, Proceeding of The International Congress, Challenges of Concrete Construction, University of Dundee, UK, Eds. Dhir, R. K„ Peter, C.H. and Laszlo, J. C„ 05 -11 September 2002, pp. 889-900 13.Tasong, W. A., lynsdale, C. J., and Cripps, J.C., Aggregate-Cement Paste Interface. II: Influence of Aggregate Physical Properties, Cement and Co