Journals / Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi / 2022 / Cilt: 24 - Sayı: 2

Static analysis of cantilever beam with geometrical discontinuity by Carrera Unified Formulation

Geometrik süreksizliğe sahip konsol kirişin Carrera birleşik formülasyonu ile statik analizi

Pages
497–514
Publication Date
2022-07-08
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Finally, the presence of a hole with different radius sizes on its cross-section subjected to the same loading is discussed.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This paper presents a numerical solution for static analysis of a rectangular cantilever beam with different sizes of a hole on its cross-section subjected to vertical concentrated load.
📊
Key Findings & Data:Then, a rectangular cantilever beam with compact cross-section subjected to vertical concentrated load is considered.
💡
Conclusion & Impact:Finally, the presence of a hole with different radius sizes on its cross-section subjected to the same loading is discussed.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Geliştirilmiş kiriş modelleri · birleşik formulasyon · CUF

Abstract

This paper presents a numerical solution for static analysis of a rectangular cantilever beam with different sizes of a hole on its cross-section subjected to vertical concentrated load. Carrera Unified Formulation (CUF) is used by employing both N-OrderTaylor type expansion (TE) and Lagrange type expansion (LE). The influence of both these different refined beam models and the different sizes of hole on the evaluation of the stress components on the cross-section along the thickness is examined. First, with the convergence study, a comparison is performed with the results obtained from the exact solution. Then, a rectangular cantilever beam with compact cross-section subjected to vertical concentrated load is considered. Finally, the presence of a hole with different radius sizes on its cross-section subjected to the same loading is discussed.

Özet

Bu çalışma, dikey tekil yük etkisinde ve kesitinde boyutları farklı olacak şekilde bir delik içeren dikdörtgen kesitli konsol bir kirişin statik analizi için sayısal bir çözüm sunmaktadır. N. mertebeden Taylor açılımı (TE) ve Lagrange açılımı (LE) uygulanarak Carrera Birleşik Formulasyonu (CUF) kullanılmıştır. Hem her iki geliştirilmiş kiriş teorisinin hem de farklı boyutlardaki deliğin, kesit üzerinde kalınlık boyunca gerilme bileşenleri üzerine etkisi incelenmiştir. İlk olarak, bir yakınsama ve kesin çözümden elde edilen sonuçlar ile bir karşılaştırma çalışması yapılmıştır. Daha sonra, tekil yük etkisinde ve kesitinde delik içermeyen dikdörtgen kesitli konsol kiriş ele alınmıştır. Son olarak da, aynı yük etkisi altında kesitte farklı yarıçaplara sahip delik olması durumu ele alınmıştır.

🔖

Cite This Article

KARATAŞ, E. E. (2022). Static analysis of cantilever beam with geometrical discontinuity by Carrera Unified Formulation. Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi, Cilt: 24 - Sayı: 2, 497–514. https://ajindex.com/articles/472753

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Timoshenko, S.P., On the corrections for shear of the differential equation for transverse vibrations of prismatic bars, Philosophical Magazine, 41, 744-746, (1921).
  2. Cowper, G.R., The shear coefficient in Timoshenko’s beam theory, Journal of Applied Mechanics, 33,2, 335-340, (1966).
  3. Pai, P.F. and Schulz, M.J., Shear correction factors and an energy consistent beam theory, International Journal of Solids and Structures, 36, 1523-1540, (1999).
  4. Gruttmann, F., et al., Shear stresses in prismatic beams with arbitrary cross-sections, International Journal for Numerical Methods in Engineering, 45, 865-889, (1999).
  5. Gruttmann, F., and Wagner, W., Shear correction factors in Tmoshenko’s beam theory for arbitrary shaped cross-section, Computational Mechanics, 27, 199-207, (2001).
  6. Hutchinson, J.R., Transverse vibrations of beams, exact versus approximate solutions, Journal of Applied Mechanics-Transactions of the Asme, 48,4, 923-928, (1981).
  7. Rychter, Z., On the shear coefficient in beam bending, Mechanics Research Communications, 14,5–6, 379–385, (1987).
  8. Mechab, I., et al., Deformation of short composite beam using refined theories, Journal of Mathematical Analysis and Applications, 346, 468-479, (2008).
  9. Dong, S.B., et al., Much ado about shear correction factors in Timoshenko beam theory, International Journal Of Solids And Structures, 47,13,, 1651-1665, (2010).
  10. Mucichescu, D.T., Bounds for stiffness of prismatic beams, Journal of Structural Engineering, 110, 1410-1414, (1984).
  11. Bekhadda, A., et al., Static buckling and vibration analysis of continuously graded ceramic-metal beams using a refined higher order shear deformation theory, Multidiscipline Modeling In Materials And Structures, 15,6, 1152-1169, (2019).
  12. Rajagopal, A., Variational Asymptotic Based Shear Correction Factor for Isotropic Circular Tubes, AIAA Journal, 57,10, 4125-4131, (2019).
  13. Wagner, W., and Gruttmann, F., A displacement method for the analysis of flexural shear stresses in thin-walled isotropic composite beams, Computers & Structures, 80,24, 1843-1851, (2002).
  14. Cai, J., and Moen, C.D., Elastic buckling analysis of thin-walled structural members with rectangular holes using generalized beam theory, Thin-Walled Structures, 107, 274-286, (2016).
  15. Taig, G., and Ranzi, G., Generalised Beam Theory (GBT) for composite beams with partial shear interaction, Engineering Structures, 99, 582-602, (2015).
  16. Carrera, E., Pagani, A., Petrolo, M., et al., Recent developments on refined theories for beams with appli