SavedAdd your journal

Journals / Anadolu Üniversitesi Bilim ve Teknoloji Dergisi :A-Uygulamalı Bilimler ve Mühendislik / 2002 / Cilt: 3 - Sayı: 2

Cam elyaf takviyeli plastikler icin çekme kuponların numerik modellenmesi

Numerical modelling of a short tensile coupon for glass fibre reinforced plastics

Mehmet SARIBIYIK
Naci ÇAĞLAR
Pages
227–234
Publication Date
2022-10-11
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The shape of the short tensile coupon is (

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Fibre reinforced plastic structural members are currently produced successfully by pultrusion and are used in a number of civil engineering applications.
📊
Key Findings & Data:The measurement of the mechanical properties of highly orthotropic material is necessary for numerical structural analysis and design.
💡
Conclusion & Impact:The shape of the short tensile coupon is (
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

Fibre reinforced plastic structural members are currently produced successfully by pultrusion and are used in a number of civil engineering applications. The measurement of the mechanical properties of highly orthotropic material is necessary for numerical structural analysis and design. The mechanical properties of composite materials are determined by specific coupon test methods or by analytical models. However, pultruded or moulded fibre reinforced plastic structural sections and components may not possess the dimensions to permit the extraction of standard length coupons, as defined by the most commonly used standards, for the determination of material properties. The shape of the short tensile coupon is (

Özet

Cam elyafı takviyeli plastik yapı elemanları ön gerilmeli olarak üretilmekte ve birçok inşaat mühendisliği alanında kullanılmaktadır. Nümerik analiz ve tasarımların yapılabilmesi için ortotropik malzemelerin mekanik özelliklerinin bilinmesi gerekir. Kompozit malzemelerin mekanik özellikleri özel test metodu ile ya da analitik olarak bulunabilir. Ancak çekilmiş ya da kalıplanmış cam elyaf takviyeli yapı profilleri çekme deneyi için gerekli standart numune boyunu vermeyebilir. İstenilen boydaki (

🔖

Cite This Article

SARIBIYIK, M., ÇAĞLAR, N. (2022). Cam elyaf takviyeli plastikler icin çekme kuponların numerik modellenmesi. Anadolu Üniversitesi Bilim ve Teknoloji Dergisi :A-Uygulamalı Bilimler ve Mühendislik, Cilt: 3 - Sayı: 2, 227–234. https://ajindex.com/articles/438509

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (5)

  1. Abd-El-Naby, S.F.M. (1992). Experimental and Theoretical Investigation of Bolted Joints for Pultru-ded Composite Structures. PhD Thesis, Dep. of Civil Engineering, University of Surrey. Anon. (1989). EXTREN Fibre-Glass Structural Shapes Design Manual. Strongwell, Bristol, Virginia. ASTM D3039 (1996). Standard Test Method for Tensile Properties of Polymeric Composite Materials. Annual Book of ASTM Standards, Vol. 14.02. Cron, S.M., Plazotto, A.N. and Sandhu, R.S. (1988). The Improvement of End-Boundary Conditions for Off-Axis Tension Specimen Use. Experimental Mechanics 28, 14-19.
  2. Davalos. J.F., Salim, H.A., Qiao, P., Lopez-Anido, R. and Barbero, E.J. (19%). Analysis and Design of Pultruded FRP Shapes under Bending. Composites Part B. 27B, 295-305.
  3. Foss, B.C., Wolfe, W. E. and Sandhu, R.S. (1992). The Effect of Tab Orientation on the Distribution of Strains in Composite Specimens. Composite Materials: Testing and Design, Vol.10, Ed.: G.C. Grimes, pp. 103-113, ASTM STP1120, American Society of Testing and Materials, Philadelphia. Kural, M.H., and Flaggs, D.L. (1983). A Finite Element Analysis Composite Tension Specimens. Composites Technology and Research 5, 11-17.
  4. Mallick, P. K. (1997). Composite Engineering Handbook. Marcel Dekker, New York. Sandhu, R. S. and Sendeckyj, G. P. (1985). On Design of Off-Axis specimen. Technical Report, AF-WAL-TR-84-3098,
  5. Flight Dynamics Laboratory, Air Force Wright Aeronautical Laboratories, Wright-Patterson Air Force Base, Ohio. Sarıbıyık, M. (2000). Analysis of a Bonded connector for Pultruded G.R.P. Structural Elements. Ph.D. Thesis, University of Newcastle, U.K.