SavedAdd your journal

Journals / Sigma Mühendislik ve Fen Bilimleri Dergisi / 2014 / Cilt: 32 - Sayı: 3

THE CHARACTERIZATION OF FRONT CUTTING GEOMETRY AND SURFACE PROPERTIES IN ABRASIVE WATER JET CUTTING OF ALUMINUM ALLOY MATERIALS

Adnan AKKURT
Pages
261–276
Publication Date
2014-09-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The aluminum alloys were used as workpiece regarding an uneasy machining material for AWJ and the experimental results were evaluated.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:It has been compulsory to use unusual machining methods, against the developments in the manufacturing sector.
📊
Key Findings & Data:The Abrasive Water Jet (AWJ) method is the least known and common one.
💡
Conclusion & Impact:The aluminum alloys were used as workpiece regarding an uneasy machining material for AWJ and the experimental results were evaluated.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Abrasive waterjet · cut front geometry · surface properties

Abstract

It has been compulsory to use unusual machining methods, against the developments in the manufacturing sector. The Abrasive Water Jet (AWJ) method is the least known and common one. Unknown aspects of the method makes limited use. The AWJ method shows various surface roughness values depend on the cutting depth although capable of cutting all kinds of materials. So that caused to adversely affected the widespread use of the method. The cutting front geometry consists to opposite direction of the feeding is another negative ways beside on the adversely effects on the cut surface properties on workpiece. In this study, the modelling of cutting front geometry was considered to provide a positive impact on expand the usability of AWJ methods. The aluminum alloys were used as workpiece regarding an uneasy machining material for AWJ and the experimental results were evaluated.

🔖

Cite This Article

AKKURT, A. (2014). THE CHARACTERIZATION OF FRONT CUTTING GEOMETRY AND SURFACE PROPERTIES IN ABRASIVE WATER JET CUTTING OF ALUMINUM ALLOY MATERIALS. Sigma Mühendislik ve Fen Bilimleri Dergisi, Cilt: 32 - Sayı: 3, 261–276. https://ajindex.com/articles/419097

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Steinhauser, T. J., “Abrasive water jets on the cutting edge of technology”, Flow Systems, USA, (1989)
  2. A. Akkurt, “Çeşitli malzemelerin Aşındırıcı Su Jeti İle Kesilmesinde Yüzey Özellikleri, Sertlik ve Mikro yapı Değişimlerinin Farklı Kesme Yöntemleriyle Karşılaştırmalı Olarak İncelenmesi”, Doktora Tezi, Gazi Üniversitesi Fen Bilimleri Enstitüsü, Ankara, (2002)
  3. Niu, M., Fukunishi, Y., Sawamura T., “Control of striated roughness on the surface cut by abrasive water jet”, BHR Group Jetting Technology, pp. 769-777 Ishinomaki Senshu University, Japan, (1996)
  4. Momber, A. W., Kovacevic, R., Schüneman, R., et al, “The influence of abrasive grain size distribution parameters on the abrasive water jet machining process”, In: Rajukar KP (ed) 1996 Proc. 25 th North American Manuf. Engrs, Dearborn, pp 21-26, (1996)
  5. Mozurkiwicz, M., Fincuan, L., Ferguson, R., “Investigation of abrasive cutting head internal parameters”, In.:Woods P A (ed) 1988 Proc.9 th. Int. Symp. Jet Cutting Techn, BHRA Fluid Engng Cranfield, (1988)
  6. Ohlsson, L., “The theory and practice of abrasive water jet cutting”, PhD Thesis, Lulea University of Technology, Sweden, (1995)
  7. Juo, N. S., Louis, H., Meier, G., “Surface structure and kerf geometry in abrasive water jet cutting: formation and optimization”, Proceedings of the7th American Waterjet Conference, USA, 1 – 26 (1993)
  8. Orbanic, H. Junkar, M. “Analysis of striation formation mechanism in abrasive water jet cutting” Wear Volume 265, Issues 5–6, 25 August 2008, Pages 821–830
  9. Maros, Z., “Energy Approach of the Taper at Abrasıve Waterjet Cuttıng” Production Processes and Systems, vol. 6. (2013) No. 1. pp. 89-96
  10. Kong, M. C., Axinte, D., “Response of titanium aluminide alloy to abrasive waterjet cutting: geometrical accuracy and surface integrity issues versus process parameters” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 2009 Volume 223: 19-42
  11. Singh, P. L., Chen, W.L., Munoz, I., “Comprehensive evaluation of abrasive waterjet cut surface quality”, 6th American Water Jet Conference, pp. 139-161, Houston, USA, (1991)
  12. Akkurt, A., “Cut Front Geometry Characterization in Cutting Applications of Brass with Abrasive Water Jet” Journal of Materials Engineering and Performance Volume 19(4) June 2010—599
  13. Akkurt, A., “The Cutting Front Side Geometry in The Applications of D3 Cold Work Tool Steel Material Via Abrasive Water Jet”, Gazi Uni