Journals / Electrica / 2021 / Cilt: 21 - Sayı: 3

Effect of Flux Barrier Shape on Performance of Single-Phase Line Start Synchronous Reluctance Motor Modified from Single Phase Induction Motor

Journal
Electrica
Pages
322–341
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results demonstrate that the efficiency of the motor is considerably dependent on these prescribed parameters, and the optimum performance is noted for the barrier position of 25 mm and barrier width of 2 mm for the designated cases.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Single-phase induction motors (SPIM) are extensively used in many industrial, commercial, and household applications.
📊
Key Findings & Data:The performance is determined by simulations with the FEM Ansys Maxwell software.
💡
Conclusion & Impact:The results demonstrate that the efficiency of the motor is considerably dependent on these prescribed parameters, and the optimum performance is noted for the barrier position of 25 mm and barrier width of 2 mm for the designated cases.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

Single-phase induction motors (SPIM) are extensively used in many industrial, commercial, and household applications. These motors are therefore required to be highly efficient and cost-effective. As the efficiency is inherently compromised for these motors, enhancement in the operating efficiency is of prime importance. This work dealt with the single-phase induction motor for increasing the efficiency by converting it to a line-start synchronous reluctance motor (LS-SynRM). However, the effect of change in the barrier shapes, such as line angle or arc shape, and the introduction of a hyperbolic barrier in the rotor are considered. The performance is determined by simulations with the FEM Ansys Maxwell software. The 0.5HP SPIM is considered for analysis. The detailed comparative parametric sensitivity analysis is carried out on rotor parameters such as barrier shape, barrier position, barrier width, rib width, and pole arc to pole pitch ratio. The results demonstrate that the efficiency of the motor is considerably dependent on these prescribed parameters, and the optimum performance is noted for the barrier position of 25 mm and barrier width of 2 mm for the designated cases. This paper also provides a detailed comparative statistical analysis of torque pulsations.

🔖

Cite This Article

CHAUDHARI, M., CHOWDHURY, A., DHOLE, G. (2021). Effect of Flux Barrier Shape on Performance of Single-Phase Line Start Synchronous Reluctance Motor Modified from Single Phase Induction Motor. Electrica, Cilt: 21 - Sayı: 3, 322–341. https://ajindex.com/articles/393419

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Global Wind Energy Council, “GWEC global wind report,” Wind Energy Technol., 2018. Available online: https://gwec.net/wp-content/uploads/2019/04/GWEC-Global-Wind-Report-2018.pdf (accessed on 1 April 2021)
  2. Turkish Wind Energy Association, Turkish Wind Energy Statistic Report. Ankara, Turkey: Turkish Wind Energy Association, 2018
  3. Z. Su, J. Wang, H. Lu and G. Zhao, “A new hybrid model optimized by an intelligent optimization algorithm for wind speed forecasting,” Energy Conversion and Management, vol. 85, pp. 443–452, 2014
  4. R. Ata, “An adaptive neuro-fuzzy inference system approach for prediction of power factor in wind turbines,” Istanbul University – Journal of Electrical and Electronics Engineering, vol. 9, no. 1, pp. 905–912, 2009
  5. W. Zhang, Z. Qu, K. Zhang, W. Mao, Y. Ma and X. Fan, “A combined model based on CEEMDAN and modified flower pollination algorithm for wind speed forecasting,” Energy Conversion and Management, vol. 136, pp. 439–451, 2017
  6. H. Liu, C. Yu, H. Wu, Z. Duan and G. Yan, “A new hybrid ensemble deep reinforcement learning model for wind speed short term forecasting,” Energy, vol. 202, 2020
  7. Y. Zhang, S. Gao, M. Ban and Y. Sun, “A method based on Lorenz disturbance and variational mode decomposition for wind speed prediction,” Advances in Electrical and Computer Engineering, vol. 19, no. 2, pp. 3–12, 2019
  8. H. Liu, H. Q. Tian, D. F. Pan and Y. F. Li, “Forecasting models for wind speed using wavelet, wavelet packet, time series and artificial neural networks,” Applied Energy, vol. 107, pp. 191–208, 2013
  9. H. Liu, X. Mi and Y. Li, “An experimental investigation of three new hybrid wind speed forecasting models using multi-decomposing strategy and ELM algorithm,” Renewable Energy, vol. 123, pp. 694–705, 2018
  10. Z. Guo, W. Zhao, H. Lu and J. Wang, “Multi-step forecasting for wind speed using a modified EMD-based artificial neural network model,” Renewable Energy, vol. 37, no. 1, pp. 241–249, 2012
  11. J. Hu, J. Wang and G. Zeng, “A hybrid forecasting approach applied to wind speed time series,” Renewable Energy, vol. 60, pp. 185–194, 2013
  12. H. Liu, C. Chen, H. Q. Tian and Y. F. Li, “A hybrid model for wind speed prediction using empirical mode decomposition and artificial neural networks,” Renewable Energy, vol. 48, pp. 545–556, 2012
  13. M. Dehghani, A. Seifi and H. Riahi-Madvar, “Novel forecasting models for immediate-short-term to long-term influent flow prediction by combining ANFIS and grey wolf optimiz