Journals / Turkish Journal of Engineering and Environmental Sciences / 2006 / Cilt: 30 - Sayı: 5

The effects of cutting tool coating on the surface roughness of AISI 1015 steel depending o cutting parameters

Pages
307–316
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The lessening of cutting speed by about 33% improves the surface roughness by about 26%, and increasing the cutting speed by about 310% resulted in an improvement of about 69%.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The effects of a number of cutting tool coating materials on the surface quality of workpieces, depending on various cutting parameters, were investigated.
📊
Key Findings & Data:AISI 1015 steel was processed without cooling on a lathe using 4 different cemented carbide cutting tools, i.e. uncoated, coated with AlTiN and coated with TiAlN using the PVD technique, and one with 3-layer coatings (outermost being TiN) applied by the CVD technique.
💡
Conclusion & Impact:The lessening of cutting speed by about 33% improves the surface roughness by about 26%, and increasing the cutting speed by about 310% resulted in an improvement of about 69%.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

The effects of a number of cutting tool coating materials on the surface quality of workpieces, depending on various cutting parameters, were investigated. AISI 1015 steel was processed without cooling on a lathe using 4 different cemented carbide cutting tools, i.e. uncoated, coated with AlTiN and coated with TiAlN using the PVD technique, and one with 3-layer coatings (outermost being TiN) applied by the CVD technique. Among the cutting parameters, the depth of cut was kept constant (2.5 mm) while the cutting speed and feed rate were changed. Five cutting speeds (50, 73, 102, 145, 205 m/min) and 2 feed rates (0.24 and 0.32 mm/rev) were used during the machining process. Coating type, feed rate and cutting speed have different effects on surface roughness. In the experiments, less average surface roughness was obtained by using a 3-layer coated tool coated outermost with TiN. The lessening of cutting speed by about 33% improves the surface roughness by about 26%, and increasing the cutting speed by about 310% resulted in an improvement of about 69%.

🔖

Cite This Article

GÖKKAYA, H., NALBANT, M. (2006). The effects of cutting tool coating on the surface roughness of AISI 1015 steel depending o cutting parameters. Turkish Journal of Engineering and Environmental Sciences, Cilt: 30 - Sayı: 5, 307–316. https://ajindex.com/articles/369147

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Altın, A., Gökkaya, H. and Nalbant, M., “The Effect of Cutting Speed in Machine Parameters on the Machinability of Inconel 718 Superalloys” J. Fac. Eng. Arch. Gazi Univ., 3, 581-586, 2006.
  2. Bayrak, M., “The Effect of Machining Parameters on Surface Roughness and Their Comparison With Expert System”, MSc Gazi University Institute of Science and Technology, Ankara, Turkey,2002.
  3. Boothroyd, G., “Fundamentals of Metal Machining and Machine Tools”, International Student ed., McGraw-Hill, New York, 1981.
  4. DeGarmo, P.E., Black, J.T. and Ronaldo A.K., Materials and Processes in Manufacturing, Prentice Hall International Inc., Upper Saddle River, NJ, USA, 1997.
  5. Eriksen, E., “Influence from Production Parameters on the Surface Roughness of a Machined Short Fibre Reinforced Thermoplastic”, International Journal of Machine Tools & Manufacture, 39, 1611-1618, 1998.
  6. Feng, C. and Wang, X., “Development of Empirical Models for Surface Roughness Prediction in Finish Turning”, International Journal of Advanced Manufacturing Technology, 20, 1-8, 2002.
  7. Gadelmavla, E.S. and Koura, M.M., “Roughness Parameter”, Journal of Material Processing Technology, 123, 133-145 2002.
  8. Ghani, A.K. and Choudhury, I.A., “Study of Tool Life Surface Roughness and Vibration in Machining Nodular Cast Iron With Ceramic Tool”, Journal of Material Processing Technology, 127, 17-22, 2002.
  9. Gokkaya, H., Sur, G. and Dilipak, H., “Experimental Investigating of the Effect of Cemented Carbide Cutting Tools Coated by PVD and CVD on Surface Roughness According to Machining Parameters”, Journal of Zonguldak Karaelmas University, Technical Education Faculty, 3-4, 473-478, 2004. ISO 4287, Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters, 1997.
  10. Kopac, J. and Bahor, M., “Interaction of the Technological History of a Workpiece Material and the Machining Parameters on the Desired Quality of the Surface Roughness of a Product,” Journal of Materials Processing Technology, 92-93, 381-387, 1999.
  11. Lin, W.S. and Lee, B.Y., “Modeling the Surface Roughness and Cutting Forces During Turning”, Journal of Material Processing Technology, 108, 286-293, 2001.
  12. Ozses, B., “The Effect of the Different Machining Conditions on the Surface Roughness on CNC Machine Tools”, MSc Gazi University Institute of Science and Technology, 2002.
  13. Özel, T. and Karpat, Y., “Predictive modeling of surface roughness and tool wear in hard turning using regression and neural network