SavedAdd your journal

Journals / Tekstil Maraton / 2003 / Cilt: 13 - Sayı: 67

An investigation about effects of drawframe passage number on OE-rotor yarn quality

Cer pasaj sayısının OE-rotor iplik kalitesine etkilerinin incelenmesi

Sibel KAPLAN
Özer GÖKTEPE
Pages
30–37
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Finally, some results were obtained about choosing the number of drawframe passage according to raw material and yarn characteristics.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, effects of drawframe passage number on rotor yarn quality were investigated.
📊
Key Findings & Data:Coarse (8's Ne), medium (20's Ne) and fine (30's Ne) rotor yarns were spun from five types of slivers (card sliver, slivers produced by one, two and three passages of drawframe processes and slivers produced by processing card sliver with an autolevelled drawframe) and quality parameters of these yarns were compared.
💡
Conclusion & Impact:Finally, some results were obtained about choosing the number of drawframe passage according to raw material and yarn characteristics.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, effects of drawframe passage number on rotor yarn quality were investigated. Coarse (8's Ne), medium (20's Ne) and fine (30's Ne) rotor yarns were spun from five types of slivers (card sliver, slivers produced by one, two and three passages of drawframe processes and slivers produced by processing card sliver with an autolevelled drawframe) and quality parameters of these yarns were compared. Finally, some results were obtained about choosing the number of drawframe passage according to raw material and yarn characteristics.

Özet

Bu makalede, şerit hazırlık işlemlerinden cer pasaj sayısının rotor iplik kalitesi üzerindeki etkileri incelenmiştir. Çalışmada, beş farklı işlem basamağıyla elde edilen şeritler (tarak şeridi, 1. pasaj cer şeridi, 2. cer pasaj şeridi 3. pasaj cer şeridi ve tarak şeridinin regüleli cer makinasına beslenmesiyle elde edilin şerit) rotor iplik makinasına beslenerek kalın (Ne 8), orta kalınlıkta (Ne 20) ve ince (Ne 30) rotor iplikleri üretilmiş ve ipliklerin kalite özellikleri karşılaştırılarak farklı hammadde ve iplik özelliklerine uygun cer pasaj sayısının seçimi konusunda sonuçlar ortaya koyulmuştur.

🔖

Cite This Article

KAPLAN, S., GÖKTEPE, Ö. (2003). An investigation about effects of drawframe passage number on OE-rotor yarn quality. Tekstil Maraton, Cilt: 13 - Sayı: 67, 30–37. https://ajindex.com/articles/359823

References (2)

  1. Anonim (Sagem), Temmuz-Ağustos 1991, Rotor Eğirmede Besleme-İplik Kalitesi ve İşleme Arasındaki Korelasyon, Sagem Bülteni, 12-16 2. Deussen, H., 1993. Rotor Spinning Technology. Schlafhorst Publications, Nort Carolina. 3. Ernst, H., 1999. Başarılı Kombinasyon: RSB-D 30 Cer Bandı ve R 20 Rotor İpliği. Melliand Türkiye Sayısı, Rieter Spinnereimaschinenbau AG. 2. 76-82. 4. Kadoğlu, H., 1993. Open-End Rotor İplikçiliği ve Bazı Kalite Faktörleri. Tekstil ve Konfeksiyon, 1, 31-40. 5. Klein, W., 1993. New Spinning Systems. Short Staple Spinning Series, Volume: 5, the Textile Institute Manual of Textile Technology, England. 6. Kong, L. X., Platfoot, R. A., 1996. Effects of Fiber Opening on the Uniformity of Rotor Spun Yarns. T.R J., 66 (1), 30-36. 7. Landwehrkamp, H., 1994. Open End (Rotor) İpliklerinde Mukavemet. Tekstil Maraton, 1. 39-46. 8. McCreight, D.J., Feil, R. W., Booterbaugh, J. H., Backe, E.E., 1997.
  2. Short Staple Yam Manufacturing, England. 9. Norusis, M. J., 1993. SPSS for Windows. Base System User's Guide, Release 6.0. USA. 10. Salhotra, K. R., Chattopadhyay, R., March-1984. Loss in Fiber Tenacity During Separation in Rotor Spinning. T.R.J., 194-197. 11. Ülkü, Ş., 1996. Hazırlık İşlemlerinin OE-Rotor İplik Özelliklerine Et kisinin Araştırılması. Tekstil Teknik, 143, 30-36.