Journals / Van Tıp Dergisi / 2020 / Cilt: 27 - Sayı: 3

Effect of Thermal Aging on Shear Bond Strength of Self Adhesive Resin Cements to Different CAD/CAM Ceramics

Termal Yaşlandırmanın Self Adeziv Rezin Simanların Farklı CAD/CAM Seramiklere Bağlantısına Etkisi

Pages
281–286
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Conclusion: The thermal aging process did not cause a significant decrease in the bond strength of self adhesive resin cements to feldpathic and lithium disilicate CAD/CAM ceramics in the short term.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Objective: The aim of this study was to evaluate the effect of short term thermal aging process on shear bond strength of self-adhesive resin cements to feldspathic and lithium disilicate CAD/CAM ceramics.
📊
Key Findings & Data:Material and Methods: 80 ceramic specimens of 1.5 mm thickness were obtained from the Vita Mark II (VIT) and IPS e.max CAD (MAX) blocks and IPS e.max CAD discs were sintered.
💡
Conclusion & Impact:Conclusion: The thermal aging process did not cause a significant decrease in the bond strength of self adhesive resin cements to feldpathic and lithium disilicate CAD/CAM ceramics in the short term.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

Objective: The aim of this study was to evaluate the effect of short term thermal aging process on shear bond strength of self-adhesive resin cements to feldspathic and lithium disilicate CAD/CAM ceramics. Material and Methods: 80 ceramic specimens of 1.5 mm thickness were obtained from the Vita Mark II (VIT) and IPS e.max CAD (MAX) blocks and IPS e.max CAD discs were sintered. All specimens were etched with 5% hydrofluoric acid and silane was applied to the ceramic surfaces. Ceramic specimens were divided into two groups and Panavia SA (PSA) and RelyX U200 (RXU) self adhesive resin cements were applied to the ceramic surface with 3 mm diameter and 2 mm high plastic tubes. After cementation specimens were divided into two sub-groups, and half of the specimens were subjected to thermal aging at 5,000 rpm between 5-55°C in the bath for 30 sec (n=10). After thermal aging, all specimens were shear tested at a speed of 0.5 mm/sec with a Universal tester. The data were evaluated by one way ANOVA test (SPSS 23). Results: The highest shear bond strength value among the groups was measured in VIT-PSA ceramics without thermal aging (10,50 ± 2,67 MPa), while the lowest values were measured in MAX-RXU samples with thermal aging (6,81 ± 1,37 MPa) (p 0.01). Conclusion: The thermal aging process did not cause a significant decrease in the bond strength of self adhesive resin cements to feldpathic and lithium disilicate CAD/CAM ceramics in the short term.

Özet

Amaç: Bu çalışmanın amacı kısa dönem termal yaşlandırma işleminin self adeziv rezin simanların feldspatik ve lityum disilikat CAD/CAM seramiklere makaslama bağlanma dayanımına etkisinin değerlendirilmesidir. Gereç ve Yöntemler: Çalışmada kullanılmak üzere Vita Mark II (VIT) ve IPS e.max CAD (MAX) bloklardan 1,5 mm kalınlığında 80 adet seramik örnek elde edildi ve MAX seramik diskler sinterize edildi. Tüm örneklerin %5’lik hidroflorik asit ile pürüzlendirildi ve yüzeylere silan uygulandı. Seramik örnekler iki gruba ayrılarak üzerlerine 3 mm çapında ve 2 mm yüksekliğinde plastik tüpler yardımıyla Panavia SA (PSA) ve RelyX U200 (RXU) self adeziv rezin simanlar yapıştırıldı. Rezin siman yapıştırılan örnekler iki alt gruba ayrıldı ve örneklerin yarısına 5-55°C sıcaklık değişimleri arasında banyoda kalma zamanı 30 sn, transfer zamanı 10 sn olan 6 aylık ağızda kalıma denk 5,000 devire ayarlanan termal döngü cihazında termal yaşlandırma işlemi uygulandı (n=10). Yaşlandırma işleminden sonra tüm örnekler Universal bir test cihazı ile 0,5 mm/sn hızında makaslama testine tabi tutuldu. Elde edilen veriler tek yönlü ANOVA testi ile değerlendirildi (SPSS 23). Bulgular: Gruplar arasında en yüksek bağlanma değeri termal yaşlandırma yapılmayan VIT-PSA seramiklerde ölçülürken (10,50 ± 2,67 MPa), en düşük değerler termal yaşlandırma uygulanmış MAX-RXU örneklerde (6,81 ± 1,37 MPa) ölçüldü (p 0.01). Sonuç: Termal yaşlandırma işlemi kısa dönemde self adeziv rezin simanların felspatik ve lityum disilikat CAD/CAM seramiklere bağlantı dayanımı değerlerinde anlamlı bir düşüşe neden olmadı.

🔖

Cite This Article

UĞUR, M., KAVUT, I., TANRIKUT, Ö. O., AKBAL, M. M. (2020). Effect of Thermal Aging on Shear Bond Strength of Self Adhesive Resin Cements to Different CAD/CAM Ceramics. Van Tıp Dergisi, Cilt: 27 - Sayı: 3, 281–286. https://ajindex.com/articles/333835

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Edelhoff, Daniel and Oliver Brix. All-ceramic restorations in different indications: a case series. J Am Dent Assoc 2011; 142(2): 14-19
  2. Coldea, Andrea, Michael V. Swain, and Norbert Thiel. Mechanical properties of polymerinfiltrated-ceramic-network materials. Dent Mater 2013; 29(4): 419-426
  3. Alberto A, Agustin P, Isabel C, Maria GB. Comparative characterization of a novel cad-cam polymer-infiltrated-ceramic-network. J Clin Exper Dent 7.4 2015; 7(4): 495
  4. Alghazzawi, Tariq F. Advancements in CAD/CAM technology: options for practical implementation. J Prosthodont Res 2016; 60(2): 72-84
  5. Cekic-Nagas I, Canay S, Sahin E. Bonding of resin core materials to lithium disilicate ceramics: the effect of resin cement film thickness. Int J Prosthodont 2010; 23(5): 469-471
  6. Triwatana P, Noppavan N, Chantana T. Clinical performance and failures of zirconia-based fixed partial dentures: a review literature. J Adv Prosthodont 4.2 2012; 76-83
  7. Palla ES, Kontonasaki E, Kantiranis N, Papadopoulou L, Zorba T, Paraskevopoulos KM, et al. Color stability of lithium disilicate ceramics after aging and immersion in common beverages. J Prosthet Dent 2018; 119(4): 632-642
  8. Senyilmaz DP, Canay S, Heydecke G, Strub JR. Influence of thermomechanical fatigue loading on the fracture resistance of all-ceramic posterior crowns. Eur J Prosthodont Restor Dent 2010; 18(2): 50-54
  9. Guess PC, Vagopoulou T, Zhang Y, Wolkewitz M, Strub JR. Marginal and internal fit of heat pressed versus CAD/CAM fabricated all-ceramic onlays after exposure to thermomechanical fatigue. J Dent 2014; 42(2): 199-209
  10. Miyazaki T, Hotta Y, Kunii J, Kuriyama S, Tamaki Y. A review of dental CAD/CAM: current status and future perspectives from 20 years of experience. Dent Mater J 2009; 28(1): 44- 56
  11. Silva RATd, Coutinho M, Cardozo PI, Silva LAd, Zorzatto JR. Conventional dualcure versus selfadhesive resin cements in dentin bond integrity. J App Oral Sci 2011; 19(4): 355-362
  12. Brain TW Leugn, James KH Tsoi, Jukka P Matinlinna, Edmond HP Pow. Comparison of mechanical properties of three machinable ceramics with an experimental fluorophlogopite glass ceramic. J Prost. Dent 2015; 114(3): 440-446
  13. Sonmez N, Gultekin P, Turp V, Akgungor G, Sen D, Mijiritsky E. Evaluation of five CAD/CAM materials by microstructural characterization and mechanical tests: a comparative in vitro study. BMC Oral Health. 2018; 18(1): 5
  14. GB Guarda, AB Correr, LS Ga AR Costa, GA Borges, MAC S. L Correr-So