Journals / Politeknik Dergisi / 2016 / Cilt: 19 - Sayı: 4

Effects of Different Coating Materials on Tool Wear, Cutting Forces and Surface Roughness in Milling of

AISI 304 Paslanmaz Çeliğinin Frezelenmesinde Farklı Kaplama Malzemelerinin Takım Aşınmasına, Kesme Kuvvetlerine ve Yüzey Pürüzlülüğüne Etkileri

Pages
433–443
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

AlTiN coated inserts showed the worst performance during milling of AISI 304 stainless steel

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the performance of various coated cutting tools were investigated experimentally in milling of AISI 304 stainless steel.
📊
Key Findings & Data:Five cementit carbide inserts with various coating such as monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN were selected in the tests and these tools were evaluated by tool wear, cutting forces and surface roughness.
💡
Conclusion & Impact:AlTiN coated inserts showed the worst performance during milling of AISI 304 stainless steel
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:AISI 304 · frezeleme · takım kaplaması

Abstract

In this study, the performance of various coated cutting tools were investigated experimentally in milling of AISI 304 stainless steel. Five cementit carbide inserts with various coating such as monolayer TiCN, AlTiN, TiAlN and two layers TiCN + TiN and AlTiN + TiN were selected in the tests and these tools were evaluated by tool wear, cutting forces and surface roughness. TiCN + TiN coated cutting inserts gave the lowest flank wear and surface roughness values. The highest tool wear and surface roughness values were obtained with AlTiN coated cutting inserts. The lowest Fx and Fy forces were measured with TiAlN coated cutting inserts. Adhesion and coating delamination on the cutting inserts were observed with EDX analysis. AlTiN coated inserts showed the worst performance during milling of AISI 304 stainless steel

Özet

Bu çalışmada, AISI 304 paslanmaz çelik malzemenin frezelenmesinde farklı kaplanmış kesici takımların performansı deneysel araştırılmıştır. Testlerde tek katlı TiCN, AlTiN, TiAlN ve iki katlı TiCN + TiN ve AlTiN + TiN olmak üzere 5 farklı kaplamaya sahip sementit karbür takma uçlar seçilmiş ve bu takımlar takım aşınması, kesme kuvvetleri ve yüzey pürüzlülüğü baz alınarak değerlendirilmiştir. TiCN + TiN kaplanmış kesici uçlar en düşük serbest yüzey aşınması ve yüzey pürüzlülüğü değerlerini vermiştir. En yüksek takım aşınması ve yüzey pürüzlülüğü değerleri ise AlTiN kaplamalı kesici uçlar ile elde edilmiştir. En düşük Fx ve Fy kuvvetleri TiAlN kaplamalı kesici uçlar ile ölçülmüştür. EDX analizi sonucunda kesici uçlarda yapışma olduğu ve kaplamanın kalktığı gözlenmiştir. AISI 304 paslanmaz çeliğinin frezelenmesinde en kötü performansı AlTiN kaplanmış uçlar göstermiştir.

🔖

Cite This Article

KURAM, E. (2016). Effects of Different Coating Materials on Tool Wear, Cutting Forces and Surface Roughness in Milling of. Politeknik Dergisi, Cilt: 19 - Sayı: 4, 433–443. https://ajindex.com/articles/307418

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...