SavedAdd your journal

Journals / Politeknik Dergisi / 2017 / Cilt: 20 - Sayı: 4

The Effects of Critical Welding Parameters on Tensile-Shear Properties of Friction Stir Spot Welded Polyethylene

BEKİR ÇEVİK
BEHÇET GÜLENÇ
AHMET DURGUTLU
Pages
944–951
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Pin length of the stirring tool directly affected the quality of welding.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The aim of this study was to investigate the weldability of high density polyethylene via friction stir spot welding method.
📊
Key Findings & Data:Polyethylene sheets were joined with dwell times of 60 to 100 s, three different pin profiles (M6×1, M6×1.25, M6×1.5) and pin lengths of 3.75 to 4.75 mm by using rotational speed of 900 rpm and delay time of 45 s.
💡
Conclusion & Impact:Pin length of the stirring tool directly affected the quality of welding.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:FSSW · polyethylene · welding parameters

Özet

The aim of this study was to investigate the weldability of high density polyethylene via friction stir spot welding method. Polyethylene sheets were joined with dwell times of 60 to 100 s, three different pin profiles (M6×1, M6×1.25, M6×1.5) and pin lengths of 3.75 to 4.75 mm by using rotational speed of 900 rpm and delay time of 45 s. During welding processes, the temperatures were measured under the welding centers. The tensile-shear tests were performed to welded samples. Also, macrostructures of welding nuggets were examined. The small welding nuggets were formed by using the lower dwell time. The melting in welding nugget occurred in the all dwell times during the welding. The dwell time affected on the friction temperature. The key (pin) hole closed when sufficient friction temperature (dwell times of 80 and 100 s). The pin profiles directly affected the welding quality. Large screw pitch range of the pin and the small pin length from 4.5 mm negatively affected the weld fracture load. Pin length of the stirring tool directly affected the quality of welding.

🔖

Cite This Article

ÇEVİK, B., GÜLENÇ, B., DURGUTLU, A. (2017). The Effects of Critical Welding Parameters on Tensile-Shear Properties of Friction Stir Spot Welded Polyethylene. Politeknik Dergisi, Cilt: 20 - Sayı: 4, 944–951. https://ajindex.com/articles/307397

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (15)

  1. Amanat N., James N.L. and McKenzie D.R., “Welding methods for joining thermoplastic polymers for the hermetic enclosure of medical devices”, Medical Engineering & Physic, 32: 690-699, (2010)
  2. Saçak M., Polimer Teknolojisi, Gazi Kitabevi, Ankara, (2012)
  3. Choudalakis G and Gotsis A.D., “Permeability of polymer/clay nanocomposites: a review”, European Polymer Journal, 45: 967-984, (2009)
  4. Jagur-Grodzinski J., “Polymers for tissue engineering, medical devices, and regenerative medicine. Concise general review of recent studies”, Polymers for Advanced Technologies, 17: 395-418, (2006)
  5. Stewart R., “Medical plastics: new polymers offer advantages for medical devices and packaging”, Plastics Engineering, 60: 20-27, (2005)
  6. Baidya K.P., Ramakrishna S., Rahman M., Ritchie A. and Huang Z.M., “An investigation on the polymer composite medical device-external fixator”, Journal of Reinforced Plastics and Composites, 22: 563-590, (2003)
  7. Juhl T.B., Christiansen J.C. and Jensen E.A., “Mechanical testing of polystyrene/polystyrene laser welds”, Polymer Testing, 32: 475-481, (2013)
  8. Yousefpour A., Hojjati M. and Immarigeon J.P., “Fusion bonding/welding of thermoplastic composites”, Journal of Thermoplastic Composite Material,. 17: 303-341, (2004)
  9. Van de Ven J.D. and Erdman A.G., “Bridging gaps in laser transmission welding of thermoplastics”, Journal of Manufacturing Science and Engineering, 129: 1011-1018, (2007)
  10. Acherjee B., Misra D., Bose D. and Venkadeshwaran K., “Prediction of weld strength and seam width for laser transmission welding of thermoplastic using response surface methodology” Optics and Laser Technology, 41: 956-967, (2009)
  11. Zhang M.Q. and Rong M.Z., “Theoretical consideration and modeling of self-healing polymers”, J. Polymer Sci. B Polymer Phys., 50: 229–241, (2012)
  12. Yang Y.K, Dong H., Cao H., Chang Y.A. and Kou S., “Liquation of Mg alloys in friction stir spot welding”, Welding Journal, 87: 167-177, (2008)
  13. Tozaki Y., Uematsu Y. and Tokaji K., “A newly developed tool without probe for friction stir spot welding and its performance”, Journal of Materials Processing Technology, 210(6-7): 844-851, (2010)
  14. Kulekci M.K., Şık A. and Kaluç E., “Effects of tool rotation and pin diameter on fatigue properties of friction stir welded lap joints”, The International Journal of Advanced Manufacturing Technology, 36: 877-882, (2008)
  15. Bilici M.K. and Yükler A.I., “Influence of tool geometry and process parameters on