Journals / Politeknik Dergisi / 2018 / Cilt: 21 - Sayı: 3

The Effect of Explosive Ratio on Microstructure and Fatigue Properties of Austenitic Stainless Steel (AISI 316L) – S235JR Composite Materials Joined by Explosive Welding Method

Patlama Kaynağı Yöntemi ile Birleştirilen Östenitik Paslanmaz Çelik (AISI 316L) – S235JR Kompozit Malzemelerde Patlayıcı Oranının Mikroyapı ve Yorulma Özelliklerine Etkisi

Pages
527–534
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In fatigue tests applied to composite materials, a decrease was found in fatigue life of composites as a result of increase of explosive rate.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, austenitic stainless steel (AISI 316L) and S235JR plates were joined via explosion welding method, which is one of solid state welding methods, and by using two different explosive rates (R=1.5-2).
📊
Key Findings & Data:As a result of the experiment, the fluctuation occurring in the joint interface of samples was observed to be very low for low explosive rate, On the other hand, it was determined that in the sample in which higher explosive rate was used the lengths and amplitudes of waves increased in the joint interface.
💡
Conclusion & Impact:In fatigue tests applied to composite materials, a decrease was found in fatigue life of composites as a result of increase of explosive rate.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Patlamalı kaynak · patlama oranı · mikroyapı

Abstract

In this study, austenitic stainless steel (AISI 316L) and S235JR plates were joined via explosion welding method, which is one of solid state welding methods, and by using two different explosive rates (R=1.5-2). The developed composite materials microstructure was evaluated in order to see changes occurring in the joint interfaces and the hardness, and fatigue tests were carried out to determine their mechanical properties. As a result of the experiment, the fluctuation occurring in the joint interface of samples was observed to be very low for low explosive rate, On the other hand, it was determined that in the sample in which higher explosive rate was used the lengths and amplitudes of waves increased in the joint interface. An increase was determined in hardness of materials forming the composite due to deformation occurring as a result of increase of explosive rate. In fatigue tests applied to composite materials, a decrease was found in fatigue life of composites as a result of increase of explosive rate.

Özet

Bu çalışmada, östenitik paslanmaz çelik (AISI 316L) ve S235JR levhalar, katı hal kaynak yöntemlerinden olan patlama kaynak yöntemiyle iki farklı patlayıcı oranı (R=1.5-2) kullanılarak birleştirilmiştir. Elde edilen kompozit malzemelerin birleşme arayüzeylerinde meydana gelen değişimleri görmek ve mekanik özelliklerini tespit etmek amacıyla mikroyapı, sertlik ve yorulma deneyleri gerçekleştirilmiştir. Deneyler sonucunda düşük patlayıcı oranının kullanıldığı numunelerin birleşme arayüzeyinde oluşan dalgalanmanın çok düşük boyutlarda olduğu görülmüştür. Daha yüksek patlayıcı oranının kullanıldığı numunede ise artan patlayıcı oranı ile beraber arayüzeyde oluşan dalgaların boylarında ve genliklerinde bir artış meydana geldiği tespit edilmiştir. Patlayıcı oranının artmasıyla beraber oluşan deformasyondan dolayı kompoziti meydana getiren malzemelerin sertliklerinde de bir artışın meydana geldiği belirlenmiştir. Kompozit malzemelere uygulanan yorulma deneylerinde ise patlayıcı oranının artmasıyla beraber kompozitlerin yorulma ömürlerinde bir azalmanın meydana geldiği tespit edilmiştir.

🔖

Cite This Article

PAMUK, Ö. (2018). The Effect of Explosive Ratio on Microstructure and Fatigue Properties of Austenitic Stainless Steel (AISI 316L) – S235JR Composite Materials Joined by Explosive Welding Method. Politeknik Dergisi, Cilt: 21 - Sayı: 3, 527–534. https://ajindex.com/articles/307378

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (17)

  1. Kahraman N., Gülenç B., “Patlamalı Kaynak Yöntemi ile Birleştirilen Titanyum ve Bakır Levhaların Mikroyapı ve Korozyon Davranışlarının İncelenmesi”, Politeknik Dergisi, 7(2): 45-52, (2004)
  2. Durgutlu A., Gülenç B., “Patlama Kaynağıyla Paslanmaz Çelik – Bakır Levhaların Kaynaklanabilirliği ve Patlayıcı Oranının Birleşme Arayüzeyine Etkisi”, Politeknik Dergisi, 5(3): 243-247, (2002)
  3. Kearns W. H., “Explosion Welding”, Welding Handbook, AWS, 3: 264-278, 1980
  4. Patterson R.A., “Fundamentals of Explosion Welding”, ASM Handbook, 6: 160-164, (1993)
  5. Gupta R. C., Kainth G. S., “Swinging Wake Mechanism For Interface Wave Generation in Explosive Welding of Metals”, Transactions of the ASME, 57:514-521, (1990)
  6. Yang Y., Xinming Z., Zhenghua L., Qingyun L., “Adiabatic Shear Band on the Titanium Side in the Ti/Mild Steel Explosive Cladding Interface”, Acta Mater, 44 (2): 561- 565, (1996)
  7. Cown G. R., Bergmann O. R, Holdzman A. H., “Mechanism of Bond Zoneave Formation in Explosive-Clad Metals”, Metallurgial Transactions, 2: 3145-3155, (1971)
  8. Yang Y., Wang Z. M., Zhang S. R., “Some Metallurgical Behaviours of Adiabaric Share on Ti Side in the Ti/Mild Steel Explosive Cladding Interface”. Rareetal Materials and Enginering, 26: 13-17, (1997)
  9. Erza A.A., “Principles and Practice of Explosive Metal Working”, Industrial Newspaper Ltd., 276-289, (1973)
  10. James F.K., Hay D.R., “Amechanizm of Explosive Bonding”, Metallurgia Transactions, 2: 1953-1958, (1971)
  11. Reid S.R., “A Discussion of theMechanism of Interface Wave Generation in Explosive Welding”, Int. Journal of Mechanical Science, 6: 399-413, (1974)
  12. Yang Y., Li Z.H., Lu P.C., “A Temperature Distrubition Model of Explosive Cladding İnterfaceand Its Aplication”. Rare Metal Metarials and Enginering, 29 (3): 161-163, (2000)
  13. Abe A., “Numerical study of the Mechanism of Wavy Interface Generation in Explosive Welding”, JSME International Journal, 40 (3): 395-401, (1997
  14. Abe A., “Numerical Simulation of the Plastic Low Field Near the Bonding Surface of Explosive Welding”, Ournal of Materials Processing Technology, 85: 162-165, (1999)
  15. Acarer M., “Patlamalı Kaynak İşlem Parametrelerinin Birleşmeye Etkisi”, Doktora Tezi, Sakarya Üniversitesi Fen Bilimleri Enstitüsü, Sakarya, 2001
  16. Iames F. K., Hay D. R., “A Mechanizm of Explosive Bolding”, Metallurgial Transactions, 2: 1953-1958, (1971)
  17. Demirkol M., “Patlamalı Kaynak Yöntemi”, II. Ulusak Kaynak Sempozyumu, İTÜ, İstanbul, Türk