Journals / Politeknik Dergisi / 2016 / Cilt: 19 - Sayı: 4

The Effect of Ni on the Microstructure and Mechanical Properties of Nb-V Microalloyed Steels Produced by Powder Metallurgy

Toz Metalürjisi ile Üretilen Nb-V Mikroalaşım Çeliğine Ni İlavesinin Mikroyapı ve Mekanik Özellikler Üzerine Etkisi

Pages
611–616
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Results indicated that 5 wt. % Ni added PM steel showed the highest values in yield strength (YS) and ultimate tensile strength (UTS)

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this work, the effect of Ni on the microstructures and tensile behaviours of Fe matrix metarials including graphite 0.55 wt. % and (Nb-V) 0.15 wt. % were investigated.
📊
Key Findings & Data:The samples pressed at 750 MPa were produced by sintered at 1350°C temperature in the argon atmosphere for 1 h.
💡
Conclusion & Impact:Results indicated that 5 wt. % Ni added PM steel showed the highest values in yield strength (YS) and ultimate tensile strength (UTS)
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Toz metalürjisi · toz metalürjisi çelikleri · mikroyapı

Abstract

In this work, the effect of Ni on the microstructures and tensile behaviours of Fe matrix metarials including graphite 0.55 wt. % and (Nb-V) 0.15 wt. % were investigated. The samples pressed at 750 MPa were produced by sintered at 1350°C temperature in the argon atmosphere for 1 h. The microstructure of the producted PM steels was characterised by optic microscope, SEM and EDS. Results indicated that 5 wt. % Ni added PM steel showed the highest values in yield strength (YS) and ultimate tensile strength (UTS)

Özet

Bu çalışmada % ağırlıkça % 0,55 grafit ve % 0,15 (Nb-V) içeren demir esaslı malzemelerde Ni ilavesinin (% ağırlıkça 2, 3 ve 5) mikroyapı ve mekanik özellikler üzerine etkisi araştırılmıştır. 750 MPa basınçta preslenen numuneler 1350°C de argon atmosferinde 1 saat sinterlenerek üretimi gerçekleştirilmiştir. Üretilen TM çeliklerinin mikroyapısı optik mikroskop SEM ve EDS ile karakterize edilmiştir. Sonuçlar % ağırlık olarak 5 Ni ilave edilmiş TM çeliğin en yüksek akma dayanımına (A. D.) ve çekme dayanımına (Ç. D.) sahip olduğunu göstermiştir.

🔖

Cite This Article

ERDEN, M. A., TAŞÇI, M. T. (2016). The Effect of Ni on the Microstructure and Mechanical Properties of Nb-V Microalloyed Steels Produced by Powder Metallurgy. Politeknik Dergisi, Cilt: 19 - Sayı: 4, 611–616. https://ajindex.com/articles/307175

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...