Journals / Politeknik Dergisi / 2018 / Cilt: 21 - Sayı: 1

Effect of the Cutting Parameters on Surface Roughness, Power Consumption and Machine Noise in Machining of R260 Steel

R260 Çeliklerinin İşlenmesinde Kesme Parametrelerinin Yüzey Pürüzlülüğü, Güç Tüketimi ve Makine Gürültüsü Üzerine Etkileri

Pages
237–244
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The experimental results showed that the depth of cut was the most significant cutting parameter on the surface roughness.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Hadfield steels are the materials having with high wear resistance, toughness, high yield and tensile strength.
📊
Key Findings & Data:Experimental studies were carried out a real production environment using constant cutting speed, four different feed rate and six different depth of cut under heavy machining conditions.
💡
Conclusion & Impact:The experimental results showed that the depth of cut was the most significant cutting parameter on the surface roughness.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Hadfield çeliği · Sert frezeleme · yüzey pürüzlülüğü

Abstract

Hadfield steels are the materials having with high wear resistance, toughness, high yield and tensile strength. Hadfield steels, also known as rail steels, are commonly used for rail transport due to their wear, impact and fatigue strength. In this study, machining behavior of the Hadfield steels and the effect of the machining parameters on surface roughness, machine noise and power consumption were investigated under dry cutting conditions using horizontal milling machine. Experimental studies were carried out a real production environment using constant cutting speed, four different feed rate and six different depth of cut under heavy machining conditions. The influence of the milling variables on surface roughness, machine noise and power consumption were evaluated by using Analysis of variance (ANOVA). The experimental results showed that the depth of cut was the most significant cutting parameter on the surface roughness. Surface roughness value was remarkably improved with increasing depth of cut. Power consumption and machine noise were affected from increasing feed rate and depth of cut values used in the experiments.

Özet

Hadfield çelikleri yüksek aşınma direncine, tokluğa, yüksek akma ve çekme mukavemetine sahip malzemelerdir. Ray çelikleri olarak da bilinen Hadfield çelikleri aşınma, darbe ve yorulma dayanımından dolayı çoğunlukla demiryolu ulaşımında kullanılmaktadır. Bu çalışmada, Hadfield çeliklerinin işleme davranışı ve işleme parametrelerinin yüzey pürüzlülüğü, makine gürültüsü ve güç tüketimi üzerindeki etkisi kuru işleme koşullarında yatay freze tezgâhı kullanılarak araştırılmıştır. Deneysel çalışmalar, ağır işleme koşullarında sabit kesme hızı, dört farklı ilerleme hızı ve altı farklı talaş derinliğinde ve gerçek bir üretim ortamında yapıldı. Frezeleme değişkenlerinin yüzey pürüzlülüğü, makine gürültüsü ve güç tüketimi üzerindeki etkisi varyans analizi (ANOVA) kullanılarak değerlendirildi. Deneysel sonuçlar, kesme derinliğinin yüzey pürüzlülüğü üzerindeki en önemli kesme parametresi olduğunu göstermiştir. Kesme derinliğinin artmasıyla yüzey pürüzlülüğü değeri belirgin şekilde iyileşmiştir. Güç tüketimi ve makine gürültüsü, deneylerde kullanılan artan ilerleme hızı ve kesme derinliği değerlerinin artmasından etkilenmiştir.

🔖

Cite This Article

KARABULUT, Ş., ŞAHİNOĞLU, A. (2018). Effect of the Cutting Parameters on Surface Roughness, Power Consumption and Machine Noise in Machining of R260 Steel. Politeknik Dergisi, Cilt: 21 - Sayı: 1, 237–244. https://ajindex.com/articles/307133

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Kıvak T., "Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts." Measurement 50: 19-28, (2014)
  2. Kocabekir I., Tunca N., Özer O., Tümer C, Eker C.B., Özçelik S., Çuğ H., Ahlatci H., “Demir Yolu Ray Sistemlerinde Kullanılan Hadfıeld Çeliğinin Aşınma Davranışı”
  3. Uluslararası Raylı Sistemler Mühendisliği Sempozyumu (ISERSE’13), Karabük, Türkiye, 9-11 Ekim 2013
  4. Canadinc D., Sehitoglu H., Maier H. J., Chumlyakov Y. I., "Strain hardening behavior of aluminum alloyed Hadfield steel single crystals.", Acta Materialia, 53 (6): 1831-1842, (2005)
  5. Horng, Jenn-Tsong, Nun-Ming Liu, and Ko-Ta Chiang. "Investigating the machinability evaluation of Hadfield steel in the hard turning with Al2O3/TiC mixed ceramic tool based on the response surface methodology", Journal of Materials Processing Technology, 208(1): 532-541, (2008)
  6. Ghani A. K., and Choudhury I. A., "Study of tool life, surface roughness and vibration in machining nodular cast iron with ceramic tool", Journal of Materials Processing Technology,127(1): 17-22, (2002)
  7. Şeker U., and Hasirci H., "Evaluation of machinability of austempered ductile irons in terms of cutting forces and surface quality", Journal of Materials Processing Technology, 173(3): 260-268, (2006)
  8. Neşeli S. and Yaldız S., "Tornalamada Yaklaşma Açısı ve Talaş Açısına Bağlı Tırlama Titreşimlerinin Yüzey Pürüzlülüğüne Etkileri" Politeknik Dergisi, 10 (4): 383 – 389, (2007)
  9. Rech J., Dumont F., Le Bot A., Arrazola P. J., "Reduction of noise during milling operations", CIRP Journal of Manufacturing Science and Technology, 18: 39-44, (2017)
  10. Weck M., and W Melder., "Problems in assessing the noise behavior of machine tools", CIRP Annals, 26 (2): 397, (1977)
  11. Bley H., Günter K. G., Haeusler J., Noe E. L., Rosenkranz W., "Machine Concentration and Noise Annoyance in the Workshop", CIRP Annals-Manufacturing Technology, 29(1): 269-273, (1980)
  12. Bollinger J. G., "Noise - An industrial pollutant of international concern", CIRP Annals, 22(2): 197-202, (1973)
  13. Hesselbach J., Hoffmeister H.-W., Schuller B.-C. and Loeis K., "Development of an active clamping system for noise and vibration reduction", CIRP Annals-Manufacturing Technology,59 (1): 395-398, (2010)
  14. Quintana G., Ciurana J., Ferrer I. and Rodriguez C. A., "Sound mapping for identification of stability lobe diagrams in milling processes", International journal of machine to