Journals / Politeknik Dergisi / 2019 / Cilt: 22 - Sayı: 1

Investigation of Hardox 400 Steel Exposed to Heat Treatment Processes in WEDM

Pages
237–244
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The most effective parameters on kerf and MRR were determined as time off and hardox.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, microstructure, mechanical, and conductivity characteristics of Hardox 400 steel were changed with different heat treatments and effect of such characteristics on its machinability with Wire Electrical Discharge Machining (WEDM).
📊
Key Findings & Data:L18 Taquchi test design was conducted with three levels and four different parameters to determine the effect of such alterations on its machinability with WEDM and post-processing Cutting width (kerf), Surface roughness (Ra), Material removal rate (MRR) values were determined.
💡
Conclusion & Impact:The most effective parameters on kerf and MRR were determined as time off and hardox.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Hardox steel · heat treatment · microstructure

Abstract

In this study, microstructure, mechanical, and conductivity characteristics of Hardox 400 steel were changed with different heat treatments and effect of such characteristics on its machinability with Wire Electrical Discharge Machining (WEDM). Optical microscope examinations were performed to determine various characteristics, and additionally microhardness and conductivity measurements were conducted hereof. L18 Taquchi test design was conducted with three levels and four different parameters to determine the effect of such alterations on its machinability with WEDM and post-processing Cutting width (kerf), Surface roughness (Ra), Material removal rate (MRR) values were determined. Micro changes were ensured successfully by using applied heat treatments. The best kerf value was obtained from sample 6 which was tempered from 350 °C. The microstructure of this sample was composed of commonly α ferrite and few pearlites. The best Ra value was obtained from sample 3 which was tempered from 200 °C. The microstructure of this sample was composed of few α ferrite and commonly pearlites. The best MRR value was obtained from sample 5 which was tempered from 300 °C. The microstructure of this sample was composed of almost equally α ferrite and pearlites. Additionally the most effective parameters on Ra were determined as hardox and current. The most effective parameters on kerf and MRR were determined as time off and hardox.

Özet

In this study, microstructure, mechanical, and conductivity characteristics of Hardox 400 steel were changed with different heat treatments and effect of such characteristics on its machinability with Wire Electrical Discharge Machining (WEDM). Optical microscope examinations were performed to determine various characteristics, and additionally microhardness and conductivity measurements were conducted hereof. L18 Taquchi test design was conducted with three levels and four different parameters to determine the effect of such alterations on its machinability with WEDM and post-processing Cutting width (kerf), Surface roughness (Ra), Material removal rate (MRR) values were determined. Micro changes were ensured successfully by using applied heat treatments. The best kerf value was obtained from sample 6 which was tempered from 350 °C. The microstructure of this sample was composed of commonly α ferrite and few pearlites. The best Ra value was obtained from sample 3 which was tempered from 200 °C. The microstructure of this sample was composed of few α ferrite and commonly pearlites. The best MRR value was obtained from sample 5 which was tempered from 300 °C. The microstructure of this sample was composed of almost equally α ferrite and pearlites. Additionally the most effective parameters on Ra were determined as hardox and current. The most effective parameters on kerf and MRR were determined as time off and hardox.

🔖

Cite This Article

TUNCER, M. A. (2019). Investigation of Hardox 400 Steel Exposed to Heat Treatment Processes in WEDM. Politeknik Dergisi, Cilt: 22 - Sayı: 1, 237–244. https://ajindex.com/articles/307095

References (12)

  1. Aqueel S., Mufti N.A., Rakwal D., Bamberg E., "Material Removal Rate, Kerf, and Surface Roughness of Tungsten Carbide Machined with Wire Electrical Discharge Machining", Journal of Materials Engineering and Performance, 20(1): 71-76, (2011)
  2. Yan M.T., Huang P.H., "Accuracy Improvement of WireEDM by Real-Time Wire Tension Control", Int. J. Mach. Tools Manuf., 44(7–8): 807-814, (2004)
  3. Hsue A.W.J., Su H.C., "Removal Analysis of WEDM Tapering Process and Its Application to Generation of Precise Conjugate Surface", Journal of Materials Processing Technology, 149(1-3): 117-123, (2004)
  4. Rakwal D., Bamberg E., "Slicing, Cleaning and Kerf Analysis of Germanium Wafers Machined by Wire Electrical Discharge Machining", Journal of materials processing technology, 209(8): 3740-3751, (2009)
  5. Mahapatra S.S., Patnaik A., "Optimization of wire electrical discharge machining (WEDM) process parameters using Taguchi method", International Journal of Advanced Manufacturing Technology, 34(9-10): 911-925, (2007)
  6. Jangra K., Jain A., Grover S., "Optimization of multiple-machining characteristics in wire electrical discharge machining of punching die using grey relational analysis", Journal of Scientific and Industrial Research, 69: 606-612, (2010)
  7. Hari S., Khanna R., "Parametric optimization of Cryogenic treated D-3 for cutting rate in wire electrical discharge machining", J Eng. Technology, 1:(2) 59–64, (2011)
  8. Kansal H.K., Singh S., Kumar P., "Parametric optimization of powder mixed electricaldischarge machining by response surface methodology", Journal of Materials ProcessingTechnology, 169(3): 427-436, (2005)
  9. Gupta P., Khanna R., Gupta R.D., Sharma N., "Effect of process parameters on kerf width in WEDM for HSLA using response surface methodology", Journal of Engineering and Technology, 2(1): 1-6, (2012)
  10. Tosun N., Cogun C., Tosun G., "A study on kerf and materials removal rate in wire electrical discharge machining based on taguchi method", Journal of Materials Processing Technology, 152: 316-322, (2004)
  11. Chaudhary R., Rampal R., Sharma N., "Investigation and Optimization of Material Removal Rate For Wire Cut Electro Discharge Machining In EN5 Steel Using Response Surface Methodology", International Journal of Latest Trends in Engineering and Technology, 3(1): 192-199, (2013)
  12. Altuğ M., Erdem M., Ozay C., "Experimental investigation of kerf of Ti6Al4V exposed to different heat treatment processes in WEDM and optimization o