Journals / Politeknik Dergisi / 2004 / Cilt: 7 - Sayı: 4

The methods used in the measurement of cutting zone temperatures as the result of heat developed during machining

Talaş kaldırma sırasında açığa çıkan ısının kesme bölgesinde oluşturduğu sıcaklıkların ölçülmesinde kullanılan yöntemler

Pages
297–305
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In this study, the assessment of the methods developed by researchers are covered, in order to measure the temperature during the cutting process.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:During the metal cutting process, the measurement of the temperature in the tool-chip interface and the shear zone is a difficult task.
📊
Key Findings & Data:However, these methods do not give the tool-chip interface tempeature accurately.
💡
Conclusion & Impact:In this study, the assessment of the methods developed by researchers are covered, in order to measure the temperature during the cutting process.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

During the metal cutting process, the measurement of the temperature in the tool-chip interface and the shear zone is a difficult task. For the measurement of the temperature developed during cutting, various methods have been developed by the researchers. Tool-chip interface temperature is generally measured by conduction and convection. However, these methods do not give the tool-chip interface tempeature accurately. The determination of the measurement points in temperature correctly, to be small in quantity of the area affected by temperature and the existence of high temperatures in the cutting edge, are the factors that make the measurement of temperature difficult. In this study, the assessment of the methods developed by researchers are covered, in order to measure the temperature during the cutting process.

Özet

Talaş kaldırma işlemleri esnasında, takım-talaş ara yüzeyinde ve kayma bölgesinde meydana gelen sıcaklıkların ölçümü oldukça zordur. Kesme işlemi esnasında oluşan sıcaklıkların ölçümü için araştırmacılar tarafından farklı yöntemler geliştirilmiştir. Takım-talaş ara yüzeyinde oluşan sıcaklıklar genel olarak iletim ve ışınım yöntemiyle ölçülmektedir. Ancak bu yöntemlerle, takım-talaş ara yüzey sıcaklıkları istenilen tamlıkla ölçülememektedir. Sıcaklık ölçülecek noktanın doğru belirlenmesi, sıcaklıktan etkilenen alanın küçük olması ve kesici uç bölgesinde çok yüksek sıcaklıkların oluşması gibi faktörler sıcaklık ölçümünü zorlaştırmaktadır. Bu çalışma; kesme işlemi esnasında oluşan sıcaklıkları ölçmek için araştırmacılar tarafından geliştirilen yöntemlerin bir değerlendirmesini içermektedir.

🔖

Cite This Article

GÖKKAYA, H., NALBANT, M., ŞEKER, U. (2004). The methods used in the measurement of cutting zone temperatures as the result of heat developed during machining. Politeknik Dergisi, Cilt: 7 - Sayı: 4, 297–305. https://ajindex.com/articles/306832

References (15)

  1. Chow, J.G., Wright, P.K., 1998, On-line Estimation of Tool Chip Interface Temperature For a Turning Operation, Trans. ASME. J. Eng. Ind. 110, pp. 56-64
  2. Tay, A.A.O., 1993, A Review of Methods of Caculating Machining Temperature, Journal of Material Processing Technology, Vol.36, pp. 225-257
  3. Halıcı, F., Gündüz, M., 2001, Isı Geçişi, Burak Ofset, Sakarya Üniversitesi, Sakarya
  4. Derbentti, T., Genceli, O., Güngör, A, Hepbaşlı, A., İlken, Z., Özbalta, N., Özgüç, F., Parmaksızoğlu, C., Urakan, Y., (Incropera, F.P., Dewitt, D.P.,), 2001, Isı ve Kütle Geçişinin Temelleri, Literatür Yayıncılık, Dördüncü Basımdan Çeviri, İstanbul
  5. Kato, T., Fujii, H., Feb 1996, PVD Film Method for Measuring the Temperature Distribution in Cutting Tools, Journal of Engineering for Industry, Vol 118, pp. 117-122
  6. Stronkowski, J.S., Moon, K.J., 1990, Finite Element Prediction of Chip Geometry and Tool/Workpiece Temperature Distributions in Dik Metal Cutting", Journal of Eng. for Industry, Vol 112, pp. 313-318
  7. Altan, E., Kıyak, M., Şubat 1995, Talaş Kaldırma İşle minde Oluşan Sıcaklığın Ölçülmesinde Kullanılan Yöntemler, Metal-Makine Dergisi
  8. Pastacı, H., 2000, Elektrik ve Elektronik Ölçmeleri, Yıldız Teknik Üniversitesi, İstanbul
  9. Shaw, M.C., 1984, Metal Cutting Principles, Oxford University Press, London, ISBN 0-19-859002-4. pp. 594
  10. Gökkaya, H., 2004, Takım-Talaş Ara Yüzey Sıcaklığının Isıl Çift Yöntemiyle Ölçülmesi Ve Kesici Takma İle Takım Tutucu Üzerindeki Etkilerinin Sonlu Elemanlarla İncelenmesi, Doktora Tezi, G.Ü. Fen Bilimleri Enstitüsü
  11. Boy, M., 2004, Kesme Parametrelerine Bağlı Olarak Ta laş Arka Yüzey Sıcaklığının Deneysel Olarak İncelen¬ mesi", Yüksek Lisans Tezi, G.Ü. Fen Bilimleri Enstitüsü
  12. Özçatalbaş, Y., 1996,"1050, 4140 ve 8620 Çeliklerinin Isıl İşlemle Değişen Mikroyapı ve Mekanik Özelliklerine Bağlı İşlenebilirlikleri, Doktora Tezi, G.Ü. Fen Bilimleri Enstitüsü, Ankara
  13. Habalı, K., 2003, Kesici Takım Kaplama Malzemesinin Takım-Talaş Arayüzey Sıcaklığı Üzerindeki Etkisinin Deneysel Olarak Araştırılması, Doktora Tezi, G.Ü. Fen Bilimleri Enstitüsü
  14. Silva, M. Bacci da., Wallbank, j., 1999, Cutting Temperature: Prediction and Measurement Methods a Review, Journal of Materials Processing Technology 88, pp. 195-202
  15. Komanduri R., Hou, Z.B., 2001, A Review of the Experimental Techniques for the Measurement of Heat and Temperatures Generated in Some Manufacturing Processes and Tribology, Tribology International, Vol. 34,