Journals / Research on Engineering Structures and Materials / 2018 / Cilt: 4 - Sayı: 1

Evaluation of damage anisotropy induced in GFRP composite materials by an innovative ultrasonic experimental approach

Pages
35–47
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The comparison between the elastic moduli of the damaged and the undamaged composite allows us for the characterization of the above cited anisotropic tensorial damage measure.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:We present a theoretical and experimental approach for the characterization of the damage induced anisotropy superimposed to the constitutive anisotropy of fiber-reinforced composite materials.
📊
Key Findings & Data:The theoretical model here employed has been developed in the framework of the Continuum Damage Mechanics theory and allows for determining a tensorial damage measure based on the change of the elastic moduli of the composite material.
💡
Conclusion & Impact:The comparison between the elastic moduli of the damaged and the undamaged composite allows us for the characterization of the above cited anisotropic tensorial damage measure.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

We present a theoretical and experimental approach for the characterization of the damage induced anisotropy superimposed to the constitutive anisotropy of fiber-reinforced composite materials. The theoretical model here employed has been developed in the framework of the Continuum Damage Mechanics theory and allows for determining a tensorial damage measure based on the change of the elastic moduli of the composite material. Moreover, the model is general since it is applicable independently of the fibers reinforcement nature, of the presence of cracks, interlaminar voids and delamination, of the geometry of this cracks, and from of failure mechanisms of the composite materials. We perform damage experiments by using an innovative goniometric device designed and built at our laboratory (Laboratorio “M. Salvati”), and aimed at the mechanical characterization of materials. In particular, by rotating the sample into a water tank, we measure the ultrasonic “natural” velocities of the undamaged composite material along suitable propagation directions. This allows us for classifying the degree of symmetry of the material and for determining the elastic constants, also in highly anisotropic materials. Then we measure the ultrasonic velocities of the artificially damaged composite and we determine again the elastic moduli. The comparison between the elastic moduli of the damaged and the undamaged composite allows us for the characterization of the above cited anisotropic tensorial damage measure.

🔖

Cite This Article

CASTELLANO, A., FOTİ, P., FRADDOSİO, A., MARZANO, S., PİCCİONİ, M. D. (2018). Evaluation of damage anisotropy induced in GFRP composite materials by an innovative ultrasonic experimental approach. Research on Engineering Structures and Materials, Cilt: 4 - Sayı: 1, 35–47. https://ajindex.com/articles/302693

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Baste S., Audoin, B. Ultrasonic evaluation of stiffness tensor changes and associated anisotropic damage in a ceramics matrix composite. Journal of Applied Mechanics, 1994; 61: 309-16. https://doi.org/10.1115/1.2901446
  2. Baste S., Aristegui C. Induced anisotropy and crack systems orientations of a ceramic matrix composite under off-principal axis loading. Mechanics of Materials, 1998; 29: 19-41. https://doi.org/10.1016/S0167-6636(98)00003-9
  3. Margueres Ph., Meraghni F., Benzeggagh M.L. Comparison of stiffness measurements and damage investigation techniques for a fatigued and post-impact fatigued GFRP composite obtained by RTM process. Composites Part A: Applied Science & Manufacturing, 2000; 31: 151-163. https://doi.org/10.1016/S1359-835X(99)00061- 5 Margueres Ph., Meraghni F. Damage induced anisotropy and stiffness reduction evalution in composite materials using ultrasonic wave transmission. Composites Part A: Applied Science & Manufacturing, 2013; 45: 134-144. https://doi.org/10.1016/j.compositesa.2012.09.007
  4. Castellano A., Foti P., Fraddosio A., Galietti U., Marzano S., Piccioni M.D. Characterization of material damage by ultrasonic immersion test. Procedia Engineering, 2015; 109: 395-402. https://doi.org/10.1016/j.proeng.2015.06.248
  5. Balasubramaniam K., Whitney S.C. ultrasonic through - transmission characterization of thick fibre-reinforced composites. NDT & E International, 1996; 29: 225-236. https://doi.org/10.1016/S0963-8695(96)00014-X
  6. Castellano A., Foti P., Fraddosio A., Marzano S. Piccioni M.D. mechanical characterization of CFRP composites by ultrasonic immersion tests: experimental and numerical approaches. Composites Part B: Engineering, 2014; 66: 299-310. https://doi.org/10.1016/j.compositesb.2014.04.024
  7. Castellano A., Foti P., Fraddosio A., Marzano S. Piccioni M.D. mechanical characterization of apricena marble by ultrasonic immersion tests. Key Engineering Materials, 2014; 628: 109-116. https://doi.org/10.4028/www.scientific.net/KEM.628.109
  8. Castellano A., Foti P., Fraddosio A., Marzano S., Piccioni M.D. Ultrasonic immersion tests for mechanical characterization of multilayered anisotropic materials. EESMS 2014, 2014
  9. IEEE Workshop in Environmental, Energy and Structural Monitoring Systems Proceedings, Naples, Italy, September 17-18, 2014, DOI: 10.1109/EESMS.2014.6923266. https://doi.org/10.1109/EESMS.2014.6923266
  10. Castellano A., Foti P., Fraddosio A., Marzano S., Paparella F., Piccioni M.D. Monitoring applied and residual stress in materials an