Journals / Research on Engineering Structures and Materials / 2018 / Cilt: 4 - Sayı: 3

Computational modeling and Constructal Design method applied to the geometric optimization of stiffened steel plates subjected to uniform transverse load

Pages
139–149
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Even though the volume was kept constant, the optimized geometry has shown a result 9110 % better compared to the one shown by the reference plate.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The present paper shows a geometric evaluation of stiffened plates subjected to a uniformly distributed transverse loading.
📊
Key Findings & Data:A non-stiffened plate measuring 2.00 m x 1.00 m x 0.02 m was used as reference, then a constant volume ratio ϕ, equals to 0.5, was taken from the reference plate and transformed into longitudinal and transverse stiffeners.
💡
Conclusion & Impact:Even though the volume was kept constant, the optimized geometry has shown a result 9110 % better compared to the one shown by the reference plate.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

The present paper shows a geometric evaluation of stiffened plates subjected to a uniformly distributed transverse loading. For that, it was proposed a set of different geometric configurations through the Constructal Design method, which were numerically simulated. Then, by means of the Exhaustive Search technique, a geometric optimization was performed aiming to minimize the central deflection of the plate. A non-stiffened plate measuring 2.00 m x 1.00 m x 0.02 m was used as reference, then a constant volume ratio ϕ, equals to 0.5, was taken from the reference plate and transformed into longitudinal and transverse stiffeners. The geometric parameters considered as degrees of freedom were: the number of longitudinal (Nls) and transverse (Nts) stiffeners and hs/ts, which is defined by the ratio between the stiffener’s height and thickness. In order to elaborate the computational model, it is used ANSYS Mechanical APDL®, a software based on the Finite Element Method (FEM). From the results, it was possible to determine a power function for each combination of Nls and Nts that accurately described the relation between the central deflection and hs/ts. Furthermore, it was noticed a substantial influence of the geometric parameters under analyses regarding the studied structural element’s mechanical behavior. Even though the volume was kept constant, the optimized geometry has shown a result 9110 % better compared to the one shown by the reference plate.

🔖

Cite This Article

CUNHA, M. L., TROİNA, G. D. S., SANTOS, E. D. D., ROCHA, L. A. O., ISOLDI, L. A. (2018). Computational modeling and Constructal Design method applied to the geometric optimization of stiffened steel plates subjected to uniform transverse load. Research on Engineering Structures and Materials, Cilt: 4 - Sayı: 3, 139–149. https://ajindex.com/articles/302667

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (7)

  1. Timoshenko S, Woinowsky-Krieger S. Theory of Plates and Shells, McGraw-Hill, New York, NY, USA, 1976.
  2. Shanmugan N E, Liew J Y R, Thevendran V. Thin-walled Structures – Research and Development, Elsevier, Singapore, 1998.
  3. Yousif M Z, Naief N K M, Hamada Y M. Optimum height of plate stiffener under pressure effect. The 1st Regional Conference of Eng. Sci. NUCEJ Spatial ISSUE; 11(3): 459 – 468, 2008. Virág Z. Optimum design of stiffened plates for different loads and shapes of ribs. Journal of Computational and Applied Mechanics, 2004; 5(1): 165-179.
  4. Tanaka M, Bercin A N. Static bending analysis of stiffened plates using the boundary element method. Engineering Analysis with Boundary Elements, 1998; 21: 147 -154. https://doi.org/10.1016/S0955-7997(98)00002-2 Bedair O K. Influence of stiffener location on the stability of stiffened plates under compression and in-plane bending. Int. J. Mech. Sci, 1997; 39(1): 33 – 49. https://doi.org/10.1016/0020-7403(96)00017-3 Silva H B S. Análise numérica da influência da excentricidade na ligação placa-viga em pavimentos usuais de edifícios. Master Thesis, Federal University of São Carlos, São Paulo, Brazil, 2010. Bejan A. Advanced Engineering Thermodynamics 2nd Ed, Willey, New York, NY, USA, 1997.
  5. Bejan A, Lorente S. Constructal theory of generation of configuration in nature and engineering. Journal of Applied Physics 100, 041301. https://doi.org/10.1063/1.2221896 Bejan A. Shape and Structure, from Engineering to Nature, Cambrigde University Press,
  6. Cambridge, England. Bejan A, Lorente S. Design with Constructal Theory, John Wiley Sons, Hoboken, NJ, USA, 2008. https://doi.org/10.1002/9780470432709 Zienkiewicz O C. Finite Element Method in Engineering Science 2nd Edition,
  7. McGrawHill, London, England, 1971. Marinho I J P. Projeto ótimo de estruturas metálicas de arquibancadas reutilizáveis via ANSYS. Master Thesis, PUC-Rio, Rio de Janeiro, Brazil, 2002. ANSYS Inc. ANSYS User's Manual: Analysis Systems, 2009.