Journals / Research on Engineering Structures and Materials / 2019 / Cilt: 5 - Sayı: 4

Damage progression in rubble-mound breakwaters scale model tests, under a climate change storm sequence

Pages
415–426
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

However, the damage parameter assessment with the stereo-photogrammetric technique allows a more versatile evaluation, since it is possible to characterize damage in representative zones of the cross-section

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This paper describes the two-dimensional (2D) physical model tests of a rock armor breakwater, performed at LNEC´s experimental facilities, under the framework of the HYDRALAB+ project.
📊
Key Findings & Data:The tested wave conditions simulated a storm sequence where two water levels (low water and high water) were considered, as well as an increase of the wave height.
💡
Conclusion & Impact:However, the damage parameter assessment with the stereo-photogrammetric technique allows a more versatile evaluation, since it is possible to characterize damage in representative zones of the cross-section
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

This paper describes the two-dimensional (2D) physical model tests of a rock armor breakwater, performed at LNEC´s experimental facilities, under the framework of the HYDRALAB+ project. The aim of the present work was to evaluate damage evolution under future climate change scenarios, by using different damage evaluation techniques. The tested wave conditions simulated a storm sequence where two water levels (low water and high water) were considered, as well as an increase of the wave height. The water levels and the wave heights were chosen to simulate extreme events forecasted on climate change scenarios. Damage evaluation was based on the traditional counting method and on stereo-photogrammetric techniques. Test results are presented in terms of the damage parameter S and in terms of the percentage of removed armor units. The analysis is focused on the damage progression during the scale model tests, for the imposed storm sequence. The damage presents an oscillating behavior with two main damage areas corresponding to the active zones for each level, due to the variation of the water level between low-water and high-water. This behavior differs significantly from that found for the common storm sequences usually tested, where the water level does not change. Both measuring techniques lead to an intermediate damage of the cross-section breakwater. However, the damage parameter assessment with the stereo-photogrammetric technique allows a more versatile evaluation, since it is possible to characterize damage in representative zones of the cross-section

🔖

Cite This Article

FORTES, C. J., LEMOS, R., MENDONÇA, A., REIS, M. T. (2019). Damage progression in rubble-mound breakwaters scale model tests, under a climate change storm sequence. Research on Engineering Structures and Materials, Cilt: 5 - Sayı: 4, 415–426. https://ajindex.com/articles/302608

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (18)

  1. AOGHS, American Oil & Gas Historical Society. Access in: 30th March 2018.
  2. Kasper F, Barros M, Rossi R, Masetti I, Falkenberg E, Karlsen S, Waclawek I. 1997 DICASa new mooring concept for FPSO's. Offshore Technology Conference, 1997.
  3. Finucane, Mike. Details of Gryphon incident of 4th February 2011 and lessons learned. Maersk Oil
  4. Qiao D, Li B, Ou J. Comparative Analysis on Coupling Effects between an Innovative Deep Draft Platform and Different Mooring Models. Brodogradnja: Teorija i praksa brodogradnje i pomorske tehnike, 2012; 63(4), 318-328
  5. Vargas PM, Hsu TM, Lee WK. Stress concentration factors for stud-less mooring chain links in fairleads. ASME 2004 23rd International Conference on Offshore Mechanics and Arctic Engineering (pp. 909-917). American Society of Mechanical Engineers, 2004.
  6. Kumar KK, Srinivas PS, Rao DS. Modeling and Stress Analysis of Aerospace Bracket Using ANSYS And FRANC3D. International Journal of Engineering Research and Technology, 1(8), 2012
  7. Gordon RB, Brown MG, Allen EM. Mooring integrity management: a state-of-the-art review. Offshore Technology Conference
  8. DNV. (2015). OS-301. Offshore Standard, Position Mooring
  9. Lacerda T. Análise de Sistemas de Ancoragem de Plataformas Flutuantes. Projeto Final de Curso. Departamento de Mecânica Aplicada e Estruturas, 2005
  10. Nazário VC. Modelagem de Sistemas de Ancoragem Utilizando Catenária Inelástica. Projeto Final de Curso–Departamento de Mecânica Aplicada e Estruturas, 2015
  11. DNV. (2010). Environmental conditions and environmental loads
  12. Bergdahl L, Kofoed JP. Simplified Design Procedures for Moorings of Wave-Energy Converters. Structural Design of Wave Energy Devices (SDWED), deliverable, v. 2, 2015
  13. Petrobras. P-66 deixa o estaleiro rumo ao campo de Lula. Access in: 31 May 2018.
  14. ANSYS, Inc. ANSYS Mechanical APDL Theory Reference. Release 15.0
  15. Burnett DS. Finite element analysis: from concepts to applications. Prentice Hall, 1987
  16. Moussa WA. Plane Stress Bracket. Ansys Tutorial. University of Alberta, 2001
  17. ANP, Agência Nacional do Petróleo, Gás Natural e Biocomb. Access in: 3th April 2018.
  18. Dean RG, Dalrymple RA. Water wave