Journals / Research on Engineering Structures and Materials / 2020 / Cilt: 6 - Sayı: 3

Tribological properties of PPS/PA46 polymer blends

Pages
271–282
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

On the other hand, the specific wear rate is in increase while the applied load and sliding speed values are in increase.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the tribological performance of originally 40 wt.% fiber glass reinforced polyphenylene sulfide (PPS-G), polyamide 46 (PA46) and their blends were studied at dry sliding conditions.
📊
Key Findings & Data:Wear tests were performed with the configuration of a polymer pin on a rotating X40CrMoV5-1 steel disc.
💡
Conclusion & Impact:On the other hand, the specific wear rate is in increase while the applied load and sliding speed values are in increase.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

In this study, the tribological performance of originally 40 wt.% fiber glass reinforced polyphenylene sulfide (PPS-G), polyamide 46 (PA46) and their blends were studied at dry sliding conditions. The materials were mixed and extruded on the twin screw extruder. The blends were dried and tribological test specimens were manufactured by using the injection machine. Wear tests were performed with the configuration of a polymer pin on a rotating X40CrMoV5-1 steel disc. Test conditions were atmospheric conditions having 60, 90, 120 N loads and 0.5, 1.0, 1.5 m/s sliding speeds. The obtained results proved that the coefficient of friction for PPS-G, PA46 and their blends is decrease while the applied load and sliding speed values are increase. On the other hand, the specific wear rate is in increase while the applied load and sliding speed values are in increase.

🔖

Cite This Article

YILDIRIM, F., AYDIN, M., YETGİN, S. H. (2020). Tribological properties of PPS/PA46 polymer blends. Research on Engineering Structures and Materials, Cilt: 6 - Sayı: 3, 271–282. https://ajindex.com/articles/302597

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Zhang M, Zeng H, He Y, Mai K. Effect of a polyaryletherketone-bearing bulky substituent on the non-isothermal crystallization kinetics of polyphenylene sulfide. Thermochim Acta, 1995; 257: 183 - 188.
  2. Choi J, Lim S, Kim J, Choe CR. Studies of an epoxy-compatibilized poly (phenylene sulfide)/polycarbonate blend. Polymer, 1997; 38: 4401 - 4406.
  3. Gopakumar TG, Ghadage RS, Ponrathnam S, Rajan CR, Fradet A. Poly (phenylene sulfide)/liquid crystalline polymer blends: 1. Non-isothermal crystallization kinetics. Polymer, 1997; 38: 2209 - 2214.
  4. Zhou S, Zhang Q, Wu C, Huang J. Effect of carbon fiber reinforcement on the mechanical and tribological properties of polyamide6/polyphenylene sulfide composites. Material Design, 2013; 44: 493 - 499.
  5. Yang J, Xu T, Lu A, Zhang Q, Tan H, Fu Q. Preparation and properties of poly (polyphenylene sulfide)/multiwall carbon nanotube composites obtained by melt compounding. Composite Science and Technology, 2009; 69: 147 - 153.
  6. Schuster M, Araujo CCD, Atanasov V, Andersen HT, Kreuer KD, Maier J. Highly sulfonated poly (phenylene sulfone): preparation and stability issues. Macromolecules, 2009; 42: 3129 - 3137.
  7. Wang J, Li KX, He HW, Wang JL, Sun GH. Kinetic and thermodynamics analysis of water absorption in unidirectional fiber reinforced composites by polyethersulphone and polyphenylene sulfide. Colloids Surfaces A, 2011; 377: 330 - 335.
  8. Zou H, Ning N, Su R, Zhang Q, Fu Q. Manipulating the phase morphology in PPS/PA66 blends using clay. Journal of Applied Polymer Science, 2007; 106: 2238 - 2250.
  9. Ana M, Pascual D, Naffakh M. Towards the development of poly (phenylene sulphide) based nanocomposites with enhanced mechanical, electrical and tribological properties. Material Chemistry and Physics, 2012; 135: 348 - 357.
  10. Ana M, Pascual D, Naffakh M. Enhancing the thermo mechanical behaviour of poly(phenylene sulphide) based composites via incorporation of covalently grafted carbon nanotubes. Composites Part A-Applied Science, 2013; 54: 10 - 19.
  11. Deng S, Cao L