Journals / Research on Engineering Structures and Materials / 2020 / Cilt: 6 - Sayı: 3

An investigation of high temperature effect on pumice aggregate light mortars with brick flour

Pages
241–255
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

With increasing of temperatures, ultrasound speed values were reduced.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:n this study, physical and mechanical properties of pumice aggregate substituted with brick flour as mineral additive and light mortars were investigated.
📊
Key Findings & Data:At the preparation of mortars, pumice (0-4mm) as a fine aggregate and CEM I 42.5R Portland Cement were used.
💡
Conclusion & Impact:With increasing of temperatures, ultrasound speed values were reduced.
🔬Design:Lab & Field Experiment
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

n this study, physical and mechanical properties of pumice aggregate substituted with brick flour as mineral additive and light mortars were investigated. At the preparation of mortars, pumice (0-4mm) as a fine aggregate and CEM I 42.5R Portland Cement were used. Standard mortar mixing ratios were taken as fine aggregate/Cement/Water=3/1/0.5 and pumice aggregate is used as a fine aggregate. Brick flour, which is used as mineral additive, is substituted with 0%, 10%, 20% and 30% by weight of cement. The flow values of produced mortars were determined while they were in fresh form. Mortar samples were cured in standard cure pool for 28 days. Flexural and compressive strengths of the mortar samples which were cured for 7 days, were measured. Physical properties such as water absorption, porosity and unit volume weight of 28 days cured mortars were determined and flexural and compressive strengths were calculated. At the end of 28th day samples which were reached its final strength, were exposed to 200 ⁰C, 400 ⁰C, 600 ⁰C and 800 ⁰C heats in High Temperature Oven. With determining of flexural and compressive strengths after heating, strength loss between before and after heating was designated. It is observed that the flexural and compressive strengths were decreased with increasing the ratio of Brick Flour. At all temperatures, it is occurred that the ultrasound speed was decreased. With increasing of temperatures, ultrasound speed values were reduced.

🔖

Cite This Article

DÜNDAR, B., RESULOĞULLARI, E. Ç., ÇALIŞKAN, A. N. (2020). An investigation of high temperature effect on pumice aggregate light mortars with brick flour. Research on Engineering Structures and Materials, Cilt: 6 - Sayı: 3, 241–255. https://ajindex.com/articles/302596

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. W. Wang, C. Lu, Y. Li, Q. Li, An investigation on thermal conductivity of fly ash concrete after elevated temperature exposure, Constr. Build. Mater. 2017; 148-157.
  2. Yıldırım, E. Çorum'da Kullanılan Tuğla Atıklarının Tekrar Değerlendirilmesinin Araştırılması, Gazi Üniversitesi, Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, 2001; 78-83s, Ankara
  3. Yılmaz, B. Na-CMC Polielektrolik İlavesinin Puzolanlı Çimento Özelliklerine Etkisi. Dumlupınar Üniversitesi, Fen Bilimleri Enstitüsü Dergisi, 2006; 11, 143- 154
  4. Kırgız, M.S. Mermer ve Tuğla Endüstrisi Atıklarının Çimento Üretiminde Mineralojik Katkı Olarak Kullanılması. Gazi Üniversitesi, Fen Bilimleri Enstitüsü, Doktora Tezi, 2007; 228s, Ankara
  5. Hansen TC. Recycling of demolished concrete and masonry. London: E&FN SPON; 1992
  6. A.H. Akca, N. Özyurt, Effects of re-curing on microstructure of concrete after high temperature exposure, Constr. Build. Mater. 2018; 168, 431-441.
  7. X. Liang, C. Wu, Y. Su, Z. Chen, Z. Li, Development of ultra-high-performance concrete with high fire resistance, Constr. Build. Mater. 2018; 179, 400-412.
  8. I. Yüksel, R. Siddique, Ö. Özkan, Influence of high temperature on the properties of concrete made by industrial by-products as fine aggregate replacement, Constr. Build. Mater. 2011; 25 (2) 967-972.
  9. Çelik, K., (2005). Uçucu Kül, Yüksek Fırın Cürufu ve Traslı Çimentolarla Üretilen Aynı Mukavemet Sınıfındaki Harçların Dayanım ve Dayanıklılığının İncelenmesi. İstanbul Üniversitesi, Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, 62s, İstanbul
  10. Yetgin, Ş. ve Çavdar A., (2005). Doğal Puzolan katkı Oranının Çimentonun Dayanım, İşlenebilirlik, Katılaşma ve Hacim Genleşmesi Özelliklerine Etkisi. Fırat Üniversitesi Fen ve Mühendislik Bilimleri Dergisi, 17 (4), 687-692
  11. Dalkılıç, S., (2014). Tuğla Tozu Katkılı Harçlarda Donatı Korozyonunun Araştırılması. Süleyman Demirel Üniversitesi, Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, 2-15s [12] Görçiz, G. "Ülkemizde Tuğla ve Kiremit Endüstrisi", 2000'li Yıllarda Sağlıklı ve Güvenli Konutlar için Tuğla-Kiremit Paneli, TUKDER, Ankara, Ocak, 2000
  12. Aksin, E., (2007). Endüstriyel Atıklarının Tuğla ve Kiremit Üretiminde Değerlendirilmesi. Dokuz Eylül Üniversitesi, Fen Bilimleri Enstitüsü, Yüksek Lisans Tezi, 89s, İzmir. [1