Journals / Research on Engineering Structures and Materials / 2021 / Cilt: 7 - Sayı: 1

Influence of sub-glass transition heat-treatment on physical and structural properties of Cu46Zr44Al8Hf2 metallic glass

Pages
121–134
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Overall, this study suggests a direct and practical way to enhance the thermal stability and high strength retention of CuZr-based metallic glasses at elevated temperatures.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The metastability of metallic glasses (MGs) can be altered via post-heat treatment around its glass transition temperature 𝑇𝑔.
📊
Key Findings & Data:The water-cooled copper mold casting is used to produce the Cu46Zr44Al8Hf2 MGs under argon gas.
💡
Conclusion & Impact:Overall, this study suggests a direct and practical way to enhance the thermal stability and high strength retention of CuZr-based metallic glasses at elevated temperatures.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

The metastability of metallic glasses (MGs) can be altered via post-heat treatment around its glass transition temperature 𝑇𝑔. Here, the influence of the short-term heat treatment slightly below the glass transition on the thermal, thermomechanical, and structural properties are investigated. The water-cooled copper mold casting is used to produce the Cu46Zr44Al8Hf2 MGs under argon gas. Heat treatment was performed by continuous heating at 20 °C/min to 400 °C, followed by immediate cooling. Samples were characterized by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) via continuously heating through its 𝑇𝑔 and 𝑇𝑥 (crystallization temperature) and by X-ray diffraction (XRD) in Bragg-Brentano (𝜃 − 2𝜃) geometry. Main findings observed are (1) an increase in the thermal stability, 𝑇𝑥 − 𝑇𝑔, registered by DMA and DSC, (2) a remarkable drop of the relaxation enthalpy in the DSC trace calculated from the change in specific heat before 𝑇𝑔, (3) appearance of a third broad peak after heat-treatment in XRD, and (4) steady profile of 𝐸′ below 𝑇𝑔 correlated to the 𝛽-relaxation in DMA. The unexpected increase in Δ𝑇 is linked to the release of the residual stresses accumulated during fast-quenching of the molten ingot down to room temperature. This stress can be estimated as 240 MPa on the outer surface and 100 MPa in the center of the cast CuZr-MG plates, which can be eliminated by the introduced heat-treatment method. Overall, this study suggests a direct and practical way to enhance the thermal stability and high strength retention of CuZr-based metallic glasses at elevated temperatures.

🔖

Cite This Article

SARAÇ, B. (2021). Influence of sub-glass transition heat-treatment on physical and structural properties of Cu46Zr44Al8Hf2 metallic glass. Research on Engineering Structures and Materials, Cilt: 7 - Sayı: 1, 121–134. https://ajindex.com/articles/302592

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. Liao GY, Chen B, Meng QK, Wang MJ, Zhao XQ. Strain glass in defect-containing ferroelastic Ti44Ni51Nb5 alloy. Rare Metals. 2015; 34: 829 - 832.
  2. Prasad DS, Ebenezer NS, Shoba C, Pujari SR. Effect of nickel electroplating on the mechanical damping and storage modulus of metal matrix composites. Mater Res Express. 2018; 5: 116409.
  3. Kim JT, Soprunyuk V, Chawake N, Zheng YH, Spieckermann F, Hong SH, et al. Outstanding strengthening behavior and dynamic mechanical properties of in-situ Al- Al3Ni composites by Cu addition. Composites, Part B. 2020; 189: 107891.
  4. Junker P, Kochmann DM. Damage-induced mechanical damping in phase-transforming composites materials. Int J Solids Struct. 2017; 113: 132 - 146.
  5. Jin XJ, Liu JY, Jin MJ. Martensitic transformation and precursor phenomena in Au7Cu5Al4 alloys. J Alloys Compd. 2013; 577: S155 - S158.
  6. Salva HR, Fabietti LM, Ghilarducci AA, Urreta SE. Mechanical damping in nanostructured Nd60Fe30Al10 magnetic alloys. J Alloys Compd. 2010; 495: 420 - 422.
  7. Wu SK, Chang SH, Chou TY, Tong S. Low-frequency damping properties of dual-phase Mg-xLi-0.5Zn alloys. J Alloys Compd. 2008; 465: 210 - 215.
  8. Pelletier JM, Perez J, Duffrene L. Mechanical response of an oxide glass to mechanical loading-shear and volume relaxation effects: physical analysis. Acta Mater. 2000; 48: 1397 - 1408.
  9. Wang Q, Pelletier JM, Blandin JJ. Thermal stability of cerium-based bulk metallic glasses. Influence of iron addition. J Alloys Compd. 2010; 504: 357 - 361.
  10. Jeong HT, Fleury E, Kim WT, Kim DH, Hono K. Study on the mechanical relaxations of a Zr36Ti24Be40 amorphous alloy by time-temperature superposition principle. J Phys Soc Jpn. 2004; 73: 3192 - 3197.
  11. Ulutan D, Sima M, Özel T. Prediction of Machining Induced Surface Integrity Using Elastic-Viscoplastic Simulations and Temperature-Dependent Flow Softening Material Models in Titanium and Nickel-Based Alloys. Adv Mater Res. 2011; 223: 401 - 410.
  12. Wang J, Xu Y, Zhang W, Mo