Journals / Selcuk Dental Journal / 2016 / Cilt: 3 - Sayı: 3

Effect of Er-YAG laser application on shear bond strength of polymethyl methacrylate to Cr-Co Alloy

Er:YAG lazer uygulamasının Cr-Co alaşımı ve polimetil metakrilat arasındaki makaslama bağlantı kuvveti üzerine etkisi

Pages
87–91
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Although, laser irradiated test specimens showed significantly higher test results compared with control group, they showed lower values than sandblasted test specimens.Conclusion: Laser treatment is not effective as Al2O3 sandblasting for improving bond strength between the alloy and acrylic resin.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Background: The aim of the present study is to investigate the effect of Er:YAG laser treatment on bond strength between Cr-Co alloy and the acrylic resin.Methods: A total of 36 square-shaped metal alloy test specimens (10x10x3 mm) were prepared.
📊
Key Findings & Data:Specimens of each alloy were randomly divided into three treatment groups (n=12).
💡
Conclusion & Impact:Although, laser irradiated test specimens showed significantly higher test results compared with control group, they showed lower values than sandblasted test specimens.Conclusion: Laser treatment is not effective as Al2O3 sandblasting for improving bond strength between the alloy and acrylic resin.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Akrilik rezin · Er-YAG lazer · metal alaşım

Abstract

Background: The aim of the present study is to investigate the effect of Er:YAG laser treatment on bond strength between Cr-Co alloy and the acrylic resin.Methods: A total of 36 square-shaped metal alloy test specimens (10x10x3 mm) were prepared. Specimens of each alloy were randomly divided into three treatment groups (n=12). Specimens, left untreated were grouped as control, air abraded with Al2O3 and Er-YAG laser irradiated. Autopolymerized resin discs of 4 mm diameter and 5 mm in height were fabricated and aplicated on alloy specimens. The bonded specimens were stored in distilled water for 24 hours at 37°C in a humidor. They were then mounted in a loading jig and debonded in shear using a universal testing machine at a cross-head speed of 0.05 mm/min. The data were statistically analyzed.Results: Among the three test groups the highest bonding values were obtained in sandblasted test specimens. Although, laser irradiated test specimens showed significantly higher test results compared with control group, they showed lower values than sandblasted test specimens.Conclusion: Laser treatment is not effective as Al2O3 sandblasting for improving bond strength between the alloy and acrylic resin.

Özet

Amaç: Bu çalışmanın amacı Er:YAG lazer uygulamasının Cr-Co alaşım ve akrilik rezin arasındaki bağlantıya etkisinin araştırılmasıdır.Gereç ve Yöntemler: Toplamda 36 adet 2 kare şeklinde metal alaşım test örneği hazırlanmıştır (10x10x3 mm). Örnekler rastgele 3 farklı yüzey işlemi grubuna ayrılmıştır (n=12). Yüzey işlemi uygulanmamış grup kontrol grubu, Al2O3 ile kumlanmış grup ve Er:YAG lazer uygulanmış grup olarak ayrılmıştır. 4 mm genişliğinde ve 5 mm yüksekliğinde otopolimerizan akrilik rezin metal örneklere uygulanmıştır. Yapıştırılan örnekler distile suda 24 saat 37°C’ de bekletilmiştir. Daha sonra üniversal test makinesinin yükleme ucuna yerleştirilmiş ve 0.05 mm/dk hız ile kopana kadar itme uygulanmıştır. Data istatistiksel olarak analiz edilmiştir.Bulgular: Üç test grubu arasında en yüksek bağlantı değerleri kumlanmış örneklerde elde edilmiştir. Lazer uygulanmış test örnekleri kontrol grubundan istatistiksel olarak daha yüksek değerler gösterse de kumlanmış örneklerden daha düşük değerler göstermiştir.Sonuç: Metal alaşım ve akrilik rezin arasında bağlantı dayanımının güçlendirilmesi için lazer uygulaması Al2O3 ile kumlamadan daha etkili değildir

🔖

Cite This Article

DURAN, İ., URAL, Ç., SARI, M., YÜZBAŞIOĞLU, E., YILMAZ, B., KAVUT, İ. (2016). Effect of Er-YAG laser application on shear bond strength of polymethyl methacrylate to Cr-Co Alloy. Selcuk Dental Journal, Cilt: 3 - Sayı: 3, 87–91. https://ajindex.com/articles/301636

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. Akova T, Ucar Y, Tukay A, Balkaya MC, Brantley WA, 2008. Comparison of the bond strength of laser-sintered and cast base metal dental alloys to porcelain. Dent Mater, 24(10), 1400-1404.