Journals / Madencilik Dergisi / 2002 / Cilt: 41 - Sayı: 2

The determination of the sahft lining thickness of the G.L.I. deep coal zone by using numerical modelling

Sayısal modelleme ile G.L.İ. derin linyit sahası için kuyu kaplama kalınlığının belirlenmesi

Pages
23–30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It is determined that when shaft stability and rock properties are considered, the shaft lining thickness for the GLI deep coal zone should be 80 cm.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In recent years, in support design concerning underground mine openings, numerical modelling techniques were used widely.
📊
Key Findings & Data:The aim of this study is to design the thickness of the shaft which is planned to sink at the GLI deep coal zone to a depth of 540 meters below surface, using numerical modelling.
💡
Conclusion & Impact:It is determined that when shaft stability and rock properties are considered, the shaft lining thickness for the GLI deep coal zone should be 80 cm.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In recent years, in support design concerning underground mine openings, numerical modelling techniques were used widely. The aim of this study is to design the thickness of the shaft which is planned to sink at the GLI deep coal zone to a depth of 540 meters below surface, using numerical modelling. The numerical modelling program Phases was used to carry out shaft lining thickness modelling studies. It is determined that when shaft stability and rock properties are considered, the shaft lining thickness for the GLI deep coal zone should be 80 cm.

Özet

Son yıllarda, yeraltı maden açıklıkları ile ilgili tahkimat tasarımlarında yaygın bir şekilde sayısal modelleme yöntemleri kullanılmaktadır. Bu çalışmanın amacı, G.L.İ. derin linyit sahasında yüzeyden 540 metre derinlikte açılması düşünülen kuyunun kaplama kalınlığının sayısal modelleme ile tasarlanmasıdır. Kuyu kaplama kalınlığı modelleme çalışmaları Phases sayısal modelleme programı kullanılarak yürütülmüştür. G.L.İ. derin linyit sahası için, kuyu duraylılığı ve kayaç özellikleri dikkate alındığında, en uygun kuyu kaplama kalınlığının 80 cm olması gerektiği belirlenmiştir.

🔖

Cite This Article

EMİR, E., ÖNCE, G. (2002). The determination of the sahft lining thickness of the G.L.I. deep coal zone by using numerical modelling. Madencilik Dergisi, Cilt: 41 - Sayı: 2, 23–30. https://ajindex.com/articles/282260

References (7)

  1. Aghai, N., 1991; "A Model for Shaft Location Selection and Ground Control Approach to Shaft Design", O.D.T.Ü. Yüksek Lisans Tezi, Ankara.
  2. Arıoğlu, E., 1981; "Maden Kuyusu Kaplama Kalınlığının Boyutlandırılmasma Rasyonel Bir Yaklaşım", 7. Türkiye Madencilik Bilimsel ve Teknik Kongresi, TMMOB, Ankara, s.367-383.
  3. Bieniawski, Z. T., 1979; "The Geomechanics Classification in Rock Engineering Applications", Proc. Xth. Congress Int. Soc. Rock Mech. Montreux, Cilt 2, s. 41-48.
  4. Çekilmez, V., 1988; "Kütahya-Tavşanlı- Tunçbilek Bölgesi JT4 Sondajı Jeoteknik Etüdü", MTA Genel Müdürlüğü, Ankara.
  5. Emir, E., 2000; "G.L.Î. Ömerler Ocağı Hazırlık Panosu Kuyu Kaplama Tasarımı", O.G.Ü. Fen Bilimleri Enstitüsü Doktora Tezi, Eskişehir. Eskikaya, Ş., Birön, C. ve Uğur, t., 1991;;G.L.I. Derin Sahalar Yeraltı İşletme Projesi", İ.T.Ü., İstanbul.
  6. Esmek, H., Şenkal, S. ve Atakuru, N., 1993; "Ömerler-Domaniç Derin Sahalar Yeraltı İşletme Projesi", G.L.Î. Tunçbilek, Kütahya. Herget, G., 1988; "Stresses in Rock", A.A. Balkema, Rotterdam., Netherlands. Hoek, E., 1995; "Strength of Rock and Rock Masses", International Society for Rock Mechanics News Journal, Cilt 2, Sayı 2, Portugal, s. 4-16.
  7. Hoek, E., Carvalho, J.L. ve Corkum, B.T., 1992; "Plastic Hybrid Analysis of Stress for Estimation of Support", University of Toronto, Canada. Hoek, 1984; "TS 500 Betonarme Yapıların Hesap ve Yapım Kuralları", TSE, Ankara.