Journals / Mathematical and Computational Applications / 2006 / Cilt: 11 - Sayı: 1

Comparison of pressure distribution in inclined and parabolic slider bearings

Pages
65–73
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results are presented both analytically and graphically.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:An infinitely wide lubricated slider bearing consisting of connected surfaces with thirtd grade fluid as lubricant is analyzed in the present study.
📊
Key Findings & Data:Under the assumptions of the order of magnitudes of the variables, it is seen that only viscous and non-Newtonian terms have significant contributions, whereas inertia terms are negligible.
💡
Conclusion & Impact:The results are presented both analytically and graphically.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

An infinitely wide lubricated slider bearing consisting of connected surfaces with thirtd grade fluid as lubricant is analyzed in the present study. Under the assumptions of the order of magnitudes of the variables, it is seen that only viscous and non-Newtonian terms have significant contributions, whereas inertia terms are negligible. Choosing non-Newtonian effects to be smaller than the viscous effects, analytical and numerical solutions are constructed. To illustrate the mathematical model, the set of equations is to used calculate the pressure for two special forms of the slider bearings, namely inclined and parabolic slider bearings. In these two cases, the variation of pressure, for a range of fluid and bearing parameters is presented. The results are presented both analytically and graphically.

🔖

Cite This Article

BAYRAKÇEKEN, H., YÜRÜSOY, M. (2006). Comparison of pressure distribution in inclined and parabolic slider bearings. Mathematical and Computational Applications, Cilt: 11 - Sayı: 1, 65–73. https://ajindex.com/articles/280099

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. J. Wang, Effects of rheological characteristics of lubricant and surface roughness on the load capacity of a hydrodynamic slider bearing, Wear. 146, 165-177, 1991. 2.H.Hashimoto, Non-Newtonian effects on the static characteristics of one dimensional slider bearings in the inertial flow regime, ASME J. Tribol. 116, 303-309,1994. 3.Z. Wu, Non-Newtonian effects of power-lubricant slurries in hydrostatic and squeeze-film bearings, Tribol. Trans. 37, 836-842, 1994. 4.J. Peterson, W. E. Finn and D. W. Dareing, Non-Newtonian temperature and pressure effects of a lubricant slurry in a rotating hydrostatic step bearing, Tnbol. Trans, 37,857-863, 1994. 5.R. Sinhasan and K. C. Goyal, Transient response of a two-lobe journal bearing lubricated with non-Newtonian lubricant, Tribol. Int, 28, 233-239, 1995. 6.N. B. Naduvinamani, Non-Newtonian effects of second-order fluids on double- layered porous Rayleigh-step bearings, Fluid Dynamics Res, 21, 495-507, 1997. 7.M. Yurusoy and M. Pakdemirli, Lubrication of a slider bearing with a special third grade fluid, Appl.Mech. Eng, 4, 759-772, 1999. 8.S. C. Sharma, S. C. Jain and P. L. Sah, Effect of non-Newtonian behaviour of lubricant and bearing flexibility on the performance of slot-entry journal bearing,Tribol. Int, 33, 507-517, 2000. 9.M. Yurusoy, Pressure distribution in a slider bearing lubricated with second-and third-grade fluids, Math. Comput. Appl, 7, 15-22, 2002. 10.Y. K. Yang and M. C. Jeng, Thermodynamic analysis of the misaligned conical- cylinderical bearing with non-Newtonian lubricants, Tribol. Trans, 46, 161-169, 2003.