As a result of all the measurements and assessments, the results of the study show that the roller burnishing method gives the best results in terms of mechanical, metallurgical properties and hole surface quality of the material.
📌 3 Key Takeaways
🎯
Objective & Hypothesis:Surface finishing processes such as drilling, turning, reaming, grinding, honing and roller burnishing etc. are widely used in manufacturing as hole surface finishing process.
📊
Key Findings & Data:In addition to the characteristics of hole such as the surface roughness, the surface hardness and the wear resistance, the circularity and cylindricality of hole are also effective on the performance of hole.
💡
Conclusion & Impact:As a result of all the measurements and assessments, the results of the study show that the roller burnishing method gives the best results in terms of mechanical, metallurgical properties and hole surface quality of the material.
Surface finishing processes such as drilling, turning, reaming, grinding, honing and roller burnishing etc. are widely used in manufacturing as hole surface finishing process. In addition to the characteristics of hole such as the surface roughness, the surface hardness and the wear resistance, the circularity and cylindricality of hole are also effective on the performance of hole. In this paper, it is presented that different hole surface finishing processes were applied to the samples made of pure copper. As a result of all the measurements and assessments, the results of the study show that the roller burnishing method gives the best results in terms of mechanical, metallurgical properties and hole surface quality of the material.
AKKURT, A., KURT, A., ÖZDEMİR, A., ŞEKER, U. (2014). Comparison of hole surface finishing processes with roller burnishing method applied in copper materials. Gazi University Journal of Science, Cilt: 27 - Sayı: 1, 721–734. https://ajindex.com/articles/255285
Lin, Y. C., Wang, S. W. and Lai, H. Y., “The relationship between surface roughness and burnishing factor in the burnishing process”, Int. J. Adv. Manuf. Technol., 23, 666-671, (2004).
Loh, N. H. and Tam, S. C., “Effects of ball burning parameters on surface finish - a literature survey and discussion”, Precis. Eng., 10, 215-220, (1988).
Akkurt, A., “Comparison of roller burnishing method other hole surface finishing processes applied on AISI 304 austenitic stainless”, J. Mater. Perform., 10.1007/s11665-010-9718-x. (2010) doi: Akkurt, A. and Ovalı, I., “The effects of burnishing and conventional finishing processes on surface roughness and roundness of the Al 6061 aluminium parts”, Pamukkale University J. Eng. Sci., 15, 371-382, (2009).
Denkena, B., Breidenstein, B., Leon, L. and Dege, J., “Development of combined manufacturing technologies components”, Adv. Mater. Res., 137, 219-246, (2010). structural Wick, C. and Veilleux, R. F., “Tool and manufacturing engineers’ handbook”, Soc. Manuf. Eng., 3, 16-38, (1985).
Hassan, A. M., “The effects of ball- and roller- burnishing on the surface roughness and hardness of some non-ferrous metals”, J. Mater. Process. Technol., 72, 385-391, (1997).
Hassan, A. M. and Abd Al-Wahhab, O. M., “Surface characteristics of some roller burnished non-ferrous Processes, 13, 505-515, (1998).
Mater. Manuf. Rajasekariah, R. and Vaidyanathan, S., “Increasing the wear-resistance of steel components by ball burnishing”, Wear, 34, 183-188, (1975).
Nemat, M. and Lyons, A. C., “An investigation of the surface topography of ball burnished mild steel and aluminium”, Int. J. Adv. Manuf. Technol., 16, 469-473, (2000).
El-Tayeb, N. S. M., Low, K. O. and Brevern, P. V., “Enhancement of surface quality and tribological properties using ball burnishing process”, Mach. Sci. Technol., 12, 234-248, (2008).
Ovalı, İ., Akkurt, A., "Comparison of Burnishing Process with Other Methods of Hole Surface Finishing Processes Applied on Brass Materials” Materials and Manufacturing Processes, Volume 26, Issue 8, 26: pp.1064–1072, 2011
El-Tayeb, N. S. M., Low, K. O. and Brevern, P. V., “The influence of roller burnishing process on hardness and roughness of cylindrical polymer surfaces”, J. Eng. Tribol., 222, 947-955, (2008). [14] Yamasa: Roller Burnishing Technology. http://www.yamasa.com.tr/eng/index.htm (2012).
Abd Al-Wahhab, O. M., “The effects of roller- burnishing on some properties of non-ferrous metals”, MSc Thesis, Jordan University of Sci. Technol.,