Journals / Bor Dergisi / 2020 / Cilt: 5 - Sayı: 1

The effect of hexagonal boron nitride addition on presureless sintered alumina matrix composites

Hekzagonal bor nitrür ilavesinin basınçsız sinterlenmiş alumina matrisli kompozitler üzerine etkisi

Pages
40–47
Publication Date
2020-03-29
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It was determined that relative density decreased, porosity increased, elastic modulus and stiffness decreased with the increasing amount of hBN in the composite.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The structural ceramics use in biomaterials such as artificial teeth and bone applications because of their high strength, good chemical resistance, and abrasion resistance.
📊
Key Findings & Data:Alumina (Al2O3) is a good candidate for artificial tooth applications due to its high strength, high chemical resistance, and white color.
💡
Conclusion & Impact:It was determined that relative density decreased, porosity increased, elastic modulus and stiffness decreased with the increasing amount of hBN in the composite.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Alümina · Bor nitrür · Kompozit

Abstract

The structural ceramics use in biomaterials such as artificial teeth and bone applications because of their high strength, good chemical resistance, and abrasion resistance. Alumina (Al2O3) is a good candidate for artificial tooth applications due to its high strength, high chemical resistance, and white color. However, their elastic modulus and stiffness are quite high compared to human teeth and bone, so they damage the teeth and bone when used as an implant. Hexagonal boron nitride (hBN) is a white, biocompatible artificial ceramic material that is structurally similar to graphite. By changing the physical properties of Al2O3 with adding hBN, it is possible to increase the potential of use in implant applications. In this study, the physical properties of the composite were investigated by adding different amounts of nano hBN into the hBN-alumina composite. The composite powders prepared by using α-Al2O3, nano hBN and MgO as a sintering agent were shaped by the hydraulic press and pressureless sintered under a protective atmosphere. Physical properties (density, elastic and shear modulus, Poisson's ratio) of sintered samples were determined. Phase analysis (XRD) and microstructure characterization (SEM) were performed. hBN showed a homogeneous distribution in the composite. It was determined that relative density decreased, porosity increased, elastic modulus and stiffness decreased with the increasing amount of hBN in the composite.

Özet

Yapay diş, kemik uygulamaları gibi biyomalzemelerde, yüksek mukavemet, iyi kimyasal dayanım ve aşınma direnci göstermeleri nedeni ile yapısal seramikler kullanılmaktadır. Alümina (Al2O3) yüksek mukavemeti, yüksek kimyasal direnci ve beyaz renkli oluşu nedeni ile yapay diş uygulamalarına iyi bir adaydır. Ancak, insan diş ve kemiği ile karşılaştırıldığında Elastik modülü ve sertliğinin oldukça yüksek olması nedeni ile implant olarak kullanıldıklarında diş ve kemiğe zarar vermektedirler. Hekzagonal bor nitrür (hBN), yapısal olarak grafite benzeyen beyaz renkli, biyouyumlu yapay seramik bir malzemedir. hBN ilave edilerek Alumina’nın fiziksel özelliklerinin değiştirilmesi ile implant uygulamalarda kullanım potansiyelinin artırılması mümkün olabilir. Bu çalışmada, farklı oranlarda nano hBN ilavesinin hBN-alümina kompozitin fiziksel özelliklerine etkisi incelenmiştir. α-Al2O3, nano hBN ve sinterleme ilavesi olarak MgO tozları kullanılarak hazırlanan kompozit tozlar hidrolik presle şekillendirilmiş ve koruyucu atmosfer altında basınçsız sinterlenmiştir. Sinterlenen numunelerin fiziksel özellikleri (yoğunluk, elastik ve kayma modülleri, Poisson oranı) belirlenmiştir. Faz analizi (XRD) ve mikroyapı karakterizasyonları (SEM) yapılmıştır. hBN kompozit içerisinde homojen bir dağılım göstermiştir. Kompozitte hBN miktarının artması ile göreceli yoğunluğun azaldığı, gözenekliliğin arttığı, Elastik modülünün ve sertliğin düştüğü tespit edilmiştir.

🔖

Cite This Article

GÖNCÜ, Y., ONAR, İ. C., AY, N. (2020). The effect of hexagonal boron nitride addition on presureless sintered alumina matrix composites. Bor Dergisi, Cilt: 5 - Sayı: 1, 40–47. https://ajindex.com/articles/252137

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Andersson M.Odén A., A new all-ceramic crown: A dense-sintered, high-purity alumina coping with porcelain, Acta Odontol. Scand., 51 (1), 59-64, 1993
  2. Ben-Nissan B., Choi A. H.Cordingley R., Alumina Ceramics, Chap.10: Bioceramics and their Clinical Applications, Woodhead Publishing, 223-242, 2008
  3. Popat K. C., Desai T. A., Alumina, Chap 1.2: Biomaterials Science (Third Edition), Academic Press, 162-166, 2013
  4. Tayyebi S. A., Mirjalili F. H., Samadi H.Nemati A., Review of synthesis and properties of hydroxyapatite/alumina nano composite powder, Chemistry Journal., 5 (2), 8, 2015
  5. Kokubo T., Bioceramics and their clinical applications, Ed. T. Kokubo. Cambridge, England, Woodhead Pub. and Maney Pub., 784, 2008
  6. A Al-Sanabani F., Madfa A.H Al-Qudaimi N., Alumina ceramic for dental applications: A review article, American J. Mater. Res., 1 (1), 26-34, 2014
  7. Kusunose T., Kim Y. H., Sekino T., Matsumoto T., Tanaka N., Nakayama T.Niihara K., Fabrication of Al2O3/BN nanocomposites by chemical processing and their mechanical properties, J. Mater. Res., 20 (1), 183-190, 2005
  8. Tayyebi S. A., Mirjalili F.,. Samadi, H., Nemati, A., Review of synthesis and properties of hydroxyapatit/alumina nano composite powder, Chemistry Journal, 5 (2), 8, 2015
  9. Chiba A., Kimura S., Raghukandan K.Morizono Y., Effect of alumina addition on hydroxyapatite biocomposites fabricated by underwater-shock compaction, Mater. Sci. Eng., A, 350 (1), 179-183, 2003
  10. Li J., Fartash B.Hermansson L., Hydroxyapatite-alumina composites and bone-bonding, Biomaterials, 16 (5), 417-22, 1995
  11. Kim S., Kong Y. M., Lee I. S.Kim H. E., Effect of calcinations of starting powder on mechanical properties of hydroxyapatite–alumina bioceramic composite, J. Mater. Sci. Mater. Med. 13 (3), 307-310, 2002
  12. Viswanath B., Ravishankar N., Interfacial reactions in hydroxyapatite/alumina nanocomposites, Scr. Mater. 55 (10). 3, 2006
  13. Cavalcanti A. N., Foxton R. M., Watson T. F., Oliveira M. T., Giannini M., Marchi G. M., Y-TZP Ceramics: Key concepts for clinical application, Operative Dentistry, 34 (3). 344-351, 2009
  14. Moraes M. C., Elias C. N., Duailibi Filho J., Oliveira L. G. D., Mechanical properties of alumina-zirconia composites for ceramic abutments, Mater. Res. 7. 643-649, 2004
  15. Maccauro G., Lommetti P. R., Raffaelli L., Manicone P. F., Biomaterials: Applications for nanomedicine, In Tech, Rijeca, Croatia 299, 2011
  16. López J. P., Alumina, zirconia, an