Journals / Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi / 2020 / Cilt: 13 - Sayı: 1

The Effect of Cu doping on Fatigue Properties of TiZrNbN Coatings

Cu ilavesinin TiZrNbN Kaplamaların Yorulma Özelliklerine Etkisi

Pages
181–189
Publication Date
2020-03-20
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

According to the results, the microhardness of Cu doped TiZrNbN is better than TiZrNbN.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The fatigue properties are very important for cutting tools due to service life.
📊
Key Findings & Data:To investigate Cu effect on fatigue properties, TiZrNbN and Cu doped TiZrNbN coatings were deposited on M2 high speed steel using reactive closed field unbalanced magnetron sputtering (CFUBMS) in bias voltage of -80V, coating pressure of 0.33 Pa and Cu target current of 0.6 A.
💡
Conclusion & Impact:According to the results, the microhardness of Cu doped TiZrNbN is better than TiZrNbN.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:CFUBMS · çoklu geçişli çizik · TiZrNbN

Abstract

The fatigue properties are very important for cutting tools due to service life. To improve fatigue properties of cutting tools, transition metal nitrides with soft metal (Cu, Ni etc.) have been coated on cutting tool materials. To investigate Cu effect on fatigue properties, TiZrNbN and Cu doped TiZrNbN coatings were deposited on M2 high speed steel using reactive closed field unbalanced magnetron sputtering (CFUBMS) in bias voltage of -80V, coating pressure of 0.33 Pa and Cu target current of 0.6 A. Microstructure properties of the coatings were determined by X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS). Mechanical properties of the coatings were examined with microhardness tester and scratch tester. Fatigue properties of the coatings were examined using multi-pass scratch tester. According to the results, the microhardness of Cu doped TiZrNbN is better than TiZrNbN. On the other hand, the adhesion and fatigue properties of TiZrNbN are the highest.

Özet

Yorulma özellikleri, kullanım ömrü nedeniyle kesme aletleri için çok önemlidir. Kesici takımların yorulma özelliklerini iyileştirmek için kesici takım malzemeleri üzerine yumuşak metalle (Cu, Ni vb.) Geçiş metali nitrürleri kaplanmıştır. Yorulma özellikleri üzerindeki Cu etkisini araştırmak için, TiZrNbN ve Cu katkılı TiZrNbN kaplamalar, -80V'luk ön gerilim voltajında, 0.33 Pa'lık kaplama basıncı ve Cu hedef akımında 0.6 A değerinde reaktif kapalı alan dengesiz manyetik alanda sıçratma (CFUBMS) kullanılarak M2 yüksek hızlı çelik üzerinde biriktirildi. Kaplamaların mikro yapı özellikleri X-Ray Difraktometri (XRD), Taramalı Elektron Mikroskop (SEM) ve Enerji Dağıtıcı Spektroskopi (EDS) ile belirlenmiştir. Kaplamaların mekanik özellikleri microhardness test cihazı ve çizik test cihazı ile incelenmiştir. Kaplamaların yorulma özellikleri çok geçişli çizik test cihazı kullanılarak incelenmiştir. Sonuçlara göre, Cu katkılı TiZrNbN'nin mikro sertliği TiZrNbN'den daha iyidir. Öte yandan, TiZrNbN'nin yapışma ve yorulma özellikleri en yüksektir

🔖

Cite This Article

AGHDAM, H. A., KELEŞ, A., BARAN, O., TOTİK, Y., EFEOGLU, İ. (2020). The Effect of Cu doping on Fatigue Properties of TiZrNbN Coatings. Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi, Cilt: 13 - Sayı: 1, 181–189. https://ajindex.com/articles/234127

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. O. Baran, A. Keles, H. Cicek, Y. Totik, and I. Efeoglu: 'The mechanical and tribological properties of Ti Nb, V N films on the Al-2024 alloy', Surf. Coat. Technol., 2017, 332, 312-318.2. J. Stallard, S. Poulat, and D. G. Teer: 'The study of the adhesion of a TiN coating on steel and titanium alloy substrates using a multi-mode scratch tester', Tribol. Int., 2006, 39(2), 159-166.3. A. Bloyce, P. Y. Qi, H. Dong, and T. Bell: 'Surface modification of titanium alloys for combined improvements in corrosion and wear resistance', Surf. Coat. Technol., 1998, 107(2-3), 125-132.4. F. Bidev, O. Baran, E. Arslan, Y. Totik, and I. Efeoglu: 'Adhesion and fatigue properties of Ti/TiB2/MoS2 graded-composite coatings deposited by closed-field unbalanced magnetron sputtering', Surf. Coat. Technol., 2013, 215, 266-271.5. C. Montero-Ocampo, E. A. Ramirez-Ceja, and J. A. Hidalgo-Badillo: 'Effect of codeposition parameters on the hardness and adhesion of TiVN coatings', Ceramics International, 2015, 41(9), 11013-11023.6. B. A. Latella, B. K. Gan, K. E. Daviesb, D. R. McKenzie, and D. G. McCulloch: 'Titanium nitride/vanadium nitride alloy coatings: mechanical properties and adhesion characteristics', Surf. Coat. Technol., 2006, 200(11), 3605-3611.7. A. Keles, H. Cicek, O. Baran, Y. Totik, and I. Efeoglu: 'Determining the critical loads of V and Nb doped ternary TiN-based coatings deposited using CFUBMS on steels', Surf. Coat. Technol., 2017, 332, 168-173.8. I. Grimberg, V. N. Zhitomirsky, R. L. Boxman, S. Goldsmith, and B. Z. Weiss: 'Multicomponent Ti-Zr-N and Ti-Nb-N coatings deposited by vacuum arc', Surf. Coat. Technol., 1998, 108(1-3), 154-159.9. V. Y. Fominski, S. N. Grigoriev, J. P. Celis, R. I. Romanov, and V. B. Oshurko: 'Structure and mechanical properties of W-Se-C/diamond-like carbon and W-Se/diamond-like carbon bi-layer coatings prepared by pulsed laser deposition', Thin Solid Films, 2012, 520(21), 6476-6483.10. Y. Alajlani, F. Placido, D. Gibson, H. O. Chu, S. G. Song, L. Porteous, and S. Moh: 'Nanostructured ZnO films prepared by hydro-thermal chemical deposition and microwave-activated reactive sputtering', Surf. Coat. Technol., 2016, 290, 16-20.11. F. Movassagh-Alanagh, A. Abdollah-Zadeh, M. Aliofkhazraei, and M. Abedi: 'Improving the wear and corrosion resistance of Ti-6Al-4V alloy by deposition of TiSiN nanocomposite coating with pulsed-DC PACVD', Wear, 2017, 390-391, 93-103.12. F. X. Ye and X. Sun: 'Nanoindentation response analysis of TiN-Cu coating deposi