SavedAdd your journal

Journals / Turkish Journal of Chemistry / 2007 / Cilt: 31 - Sayı: 1

Plasma-Initiated Polymerization of (2-Methacryloyloxyethyl) Thrimethyl Ammonium Chloride

Yangang HE
Gang LI
Jing MIAO
Xueqing YU
Fang YANG
Pages
11–16
Publication Date
2007-01-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results indicated that temperature played a very important role in controlling the solubility of Poly(MTAC) in water.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Plasma-initiated polymerization of (2-methacryloyloxyethyl) thrimethyl ammonium chloride (MTAC)) was studied.
📊
Key Findings & Data:The effects of discharge time and discharge power on temperature in a tubular-type reactor chamber were accurately tested by on-line thermocouple, and the equation relating discharge time, discharge power and temperature in the tubular-type reactor chamber was derived.
💡
Conclusion & Impact:The results indicated that temperature played a very important role in controlling the solubility of Poly(MTAC) in water.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Plasma-initiated polymerization · temperature · discharge time

Abstract

Plasma-initiated polymerization of (2-methacryloyloxyethyl) thrimethyl ammonium chloride (MTAC)) was studied. The effects of discharge time and discharge power on temperature in a tubular-type reactor chamber were accurately tested by on-line thermocouple, and the equation relating discharge time, discharge power and temperature in the tubular-type reactor chamber was derived. The results indicated that temperature played a very important role in controlling the solubility of Poly(MTAC) in water. For T \ge 130°, Poly(MTAC) was cross-linked, and the highest rate of absorbing water of Poly(MTAC) was 15 g · g-1. For T < 130°, Poly(MTAC) was linear, and the highest intrinsic viscosity of Poly(MTAC) was 420.2 cm3 · g-1. The polymerization condition of linear Poly(MTAC) was optimized as follows: discharge time 60 s and discharge power 60 W.

Özet

Plasma-initiated polymerization of (2-methacryloyloxyethyl) thrimethyl ammonium chloride (MTAC)) was studied. The effects of discharge time and discharge power on temperature in a tubular-type reactor chamber were accurately tested by on-line thermocouple, and the equation relating discharge time, discharge power and temperature in the tubular-type reactor chamber was derived. The results indicated that temperature played a very important role in controlling the solubility of Poly(MTAC) in water. For T \ge 130°, Poly(MTAC) was cross-linked, and the highest rate of absorbing water of Poly(MTAC) was 15 g · g-1. For T < 130°, Poly(MTAC) was linear, and the highest intrinsic viscosity of Poly(MTAC) was 420.2 cm3 · g-1. The polymerization condition of linear Poly(MTAC) was optimized as follows: discharge time 60 s and discharge power 60 W.

🔖

Cite This Article

HE, Y., LI, G., MIAO, J., YU, X., YANG, F. (2007). Plasma-Initiated Polymerization of (2-Methacryloyloxyethyl) Thrimethyl Ammonium Chloride. Turkish Journal of Chemistry, Cilt: 31 - Sayı: 1, 11–16. https://ajindex.com/articles/217985

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (8)

  1. J. Chen, “Plasma Chemistry and Application”. Science Press of China, 2001.
  2. X. Ge, Q. Ye and X. Xu, Radiat. Phys. Chem. 50, 253, (1997).
  3. T. Okada, I. Ishigaki, T. Suma, and S. Machi, J. Appl. Polym. Sci. 24, 1713 (1979)
  4. H. Susanna, A. Toni, K. Lauri, Polymer, 44, 7909 (2003).
  5. L. Zhang, X. Liu and C. Li, Polymer Mater. Science and Engineering, 15, 59 (1999).
  6. W. Zhang and X. Hou, Acta Polymerica Sinica, 10, 577 (2000).
  7. Z. Cheng and J. Lu, L. Fine Chemicals, 17, 658 (2000).
  8. C. Chelaru, I. Diaconu and I. Simionescu, Polymer Bulletin, 40, 757 (1998).