SavedAdd your journal

Journals / Kastamonu Üniversitesi Orman Fakültesi Dergisi / 2015 / Cilt: 15 - Sayı: 1

Effects of Fiberglass and Steel Sheet Reinforcement on the Bending Performance of Glulam Beams Constructed with Turkish Red Pine (Pinus brutia Ten.)

Kızılçamdan (Pinus brutia Ten.) Üretilen Tabakalı Kerestede Cam Lifi ve Çelik Plaka ile Güçlendirmenin Eğilme Performansına Etkisi

Ergün GÜNTEKİN
TUĞBA YILMAZ AYDIN
Pages
73–77
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Reinforcement also changed the failure mode of glulam beams tested

📌 3 Key Takeaways

🎯
Objective & Hypothesis:A study was conducted to investigate the bending performance of glulam beams constructed of Red pine reinforced by fiberglass and steel plates.
📊
Key Findings & Data:For the study, 15 full size glulam beams constructed of Turkish red pine lumber were produced.
💡
Conclusion & Impact:Reinforcement also changed the failure mode of glulam beams tested
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Kızılçam · Tabakalı kereste · Güçlendirme

Abstract

A study was conducted to investigate the bending performance of glulam beams constructed of Red pine reinforced by fiberglass and steel plates. Local reinforcement is proposed in order to improve the flexural strength and stiffness of glulam beams. For the study, 15 full size glulam beams constructed of Turkish red pine lumber were produced. All beams had similar 5 layers consisting of two finger-jointedmembers at the bottom, a single member at the fourth, six finger-jointed-members at the third and second layer and another single member at the top. Glulam beams were tested using three-point bending test to determine their load-deformation behavior. According to test results, elasticity of the glulam beams can be improved 14% and 24% using fiber glass and steel plates. Similarly, maximum load carrying capacity of glulam beams constructed of Turkish red pine lumbers may be improved 27 % and 36 % by using fiberglass and steel reinforcements, respectively. Reinforcement also changed the failure mode of glulam beams tested

Özet

Bu çalışmada kızılçam kullanılarak üretilmiş ve cam lifi ve çelik plaka ile güçlendirilmiş tabakalı kerestelerin eğilmedeki performans özellikleri araştırılmıştır. Tabakalı kerestede eğilme özelliklerini iyileştirmek için lokal güçlendirme yapılmıştır. Çalışmada kızılçam kerestesi kullanılarak 15 adet 10 x 200 x 3000 mm ölçülerinde tabakalı kereste örnekleri üretilmiştir. Bütün örneklerin en alt katmanı parmak dişle birleştirilmiş iki keresteden; üstündeki katman tek parça keresteden; orta ve üstü katman parmak dişle birleştirilmiş altı elemandan ve en üst katman ise tek elemandan oluşmaktadır. Dolayısıyla kontrol örneklerinde kırılmaların en alt tabakada parmak dişli birleştirmede olması planlanmıştır. Güçlendirme işlemi cam lifi ve çelik plaka kullanılarak gerçekleştirilmiştir. Tabakalı kereste örneklerinin üç nokta eğilme testi ile performans özellikleri belirlenmiştir. Çalışma sonuçlarına göre kızılçam kullanılarak üretilmiş tabakalı kerestelerde elastikiyet modülü cam lifi ile % 14, çelik plaka ile % 24 artmıştır. Cam lifi maksimum yük taşıma kapasitesini% 27, çelik plaka ise % 36 arttırmıştır. Güçlendirme tabakalı kirişlerde kırılma modunu da değiştirmiştir.

🔖

Cite This Article

GÜNTEKİN, E., AYDIN, T. Y. (2015). Effects of Fiberglass and Steel Sheet Reinforcement on the Bending Performance of Glulam Beams Constructed with Turkish Red Pine (Pinus brutia Ten.). Kastamonu Üniversitesi Orman Fakültesi Dergisi, Cilt: 15 - Sayı: 1, 73–77. https://ajindex.com/articles/210565

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (7)

  1. Anca P., Douglas J.G., Roberto L. 2004. Carbon fiber-vinyl ester compositere inforcement of wood using the VARTM/SCRIMP fabrication process.Composites: Part A- Applied Science and Manufacturing, 35(11), 1257-1265. André A. 2006. Fibers for strengthening of timber structures. Technical Report. Luleå University of Technology. Department of Civil and Environmental Engineering Division of Structural Engineering. SE - 971 87 LULEÅ. Bostrom L., Hoffmeyer P., Solli K.H. 1999. Tensile properties of machine strength graded timber for glued laminated timber. Proceedings of Pacific Timber Engineering Conference, Rotorua, New Zealand, (14 – 18 March 1999), 215 – 230. Buell T.W., Saadatmanesh P.E. 2005. Strengthening timber bridge beams using carbon fiber. Journal of Structural Engineering, 131(1), 173-187. Bulleit W.M. 1984. Reinforcement of wood materials A review. Wood and Fiber Science, 16 (3), 391-397.
  2. Cheng F., Hu Y. 2011. Nondestructive test and prediction of MOE of FRP reinforced fast-growing poplar Composites Technology, 71, 1163-1170.
  3. Science and Dagher H.J., Kimball T.E., Shaler S.M., 1996. reinforcement on low grade eastern hemlock glulams.General Technical Report FPL-GTR-94, USDA Forestry Products Laboratory, Madison, WI, 207-214.
  4. Effect of FRP Dagher H.J., Abdel-Magid B., Lindyberg R., Poulin J., Shalter S. 1998. Staticbending test result of Douglas-fir and western hemlock FRP- reinforced glulambeams. AEWC Report No.98-4,
  5. University of Maine AEWC Center, Orono, Marine,U.S.A. Echavarria C., Jimenez L., Ochoa J.C. 2012. Bamboo-reinforced Glulam beams: An alternative to fiberglass-reinforced glulam beams. Dyna, 174,24-30. EN 40 2003. Structural timber and glued laminated timber: Determination of some physical and mechanical properties. European Committee for Standardization. Fiorelli J., Dias, A.A. 2006. Fiberglass- reinforced Glulam Beams: Mechanical properties and theoretical model. Materials Research, 9 (3), 263-269. Jacob J.; Barragan O.L.G. 2007. Flexural strengthening of glued laminated timber beams with steel and carbon fiber reinforced polymers. Master’s Thesis in the International Master’s Programme Structural Engineering. Chalmers Unıversity of Technology, Sweden. John K.C., Lacroix S. 2000. Composite reinforcement of timber in bending. Can. J. Civ. Eng., 27, 899-906.
  6. Johnson, H., Blanksvärd, T., Carolin, A. 2006. Glulam members strengthened by carbon fiber reinforcement. Materials and Structures, 40 (1), 47-56.
  7. Moody R.C., Hernandez R. 1997. Engin