Journals / Balkan Journal of Electrical and Computer Engineering / 2026 / Volume: 14

Hardware Realization and Resource Analysis of Continuous-Time Sliding Mode State Estimators on FPGA

FPGA Üzerinde Sürekli Zamanlı Kayan Kipli Durum Kestiricilerinin Donanımsal Gerçekleştirilmesi ve Kaynak Kullanımı Analizi

Hakan Kızmaz(BATMAN ÜNİVERSİTESİ, MÜHENDİSLİK-MİMARLIK FAKÜLTESİ)0000-0001-7680-7191
Saadettin Aksoy(İstanbul Ticaret Üniversitesi Mühendislik Fakültesi)0009-0007-9312-6866
Pages
—
Publication Date
2026-10-28
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

FPGA outputs were recorded under the tested laboratory conditions, although post-fit timing analysis did not establish closure at the specified base-clock constraint.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Rotor-flux estimation on FPGA requires attention to both estimation accuracy and hardware resources.
📊
Key Findings & Data:Software Monte Carlo analysis is followed by separate FPGA experiments in which a stochastic motor reference model and one estimator operate concurrently.
💡
Conclusion & Impact:FPGA outputs were recorded under the tested laboratory conditions, although post-fit timing analysis did not establish closure at the specified base-clock constraint.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Field-programmable gate array · induction motor · Kalman–Bucy filter

Abstract

Rotor-flux estimation on FPGA requires attention to both estimation accuracy and hardware resources. This study implements sliding-mode mean-square (SMMS) and sliding-mode mean-module (SMMM) filters for an induction motor and compares them with a Kalman–Bucy (KB) implementation. The continuous-time filter equations are realized as fixed-point updates using recorded electrical signals and measured rotor speed. Software Monte Carlo analysis is followed by separate FPGA experiments in which a stochastic motor reference model and one estimator operate concurrently. Software evaluation uses model-generated stator currents, whereas the FPGA experiments feed the estimators with replayed measured currents from the same recorded operating interval. The comparison shows that the relative accuracy of the estimators varies with the noise level: the sliding mode filters achieve lower errors across several tested conditions while requiring fewer logic resources than KB. FPGA outputs were recorded under the tested laboratory conditions, although post-fit timing analysis did not establish closure at the specified base-clock constraint.

Özet

FPGA üzerinde rotor akısı kestirimi, hem kestirim doğruluğunun hem de donanım kaynaklarının dikkate alınmasını gerektirir. Bu çalışmada, bir asenkron motor için kayan kipli ortalama kare (SMMS) ve kayan kipli ortalama modül (SMMM) filtreleri gerçekleştirilmiş ve Kalman–Bucy (KB) uygulamasıyla karşılaştırılmıştır. Sürekli zamanlı filtre denklemleri, kaydedilmiş elektriksel işaretler ve ölçülen rotor hızı kullanılarak sabit noktalı güncellemeler biçiminde gerçekleştirilmiştir. Yazılım ortamındaki Monte Carlo analizini, stokastik bir motor referans modeli ile bir kestiricinin eşzamanlı çalıştığı ayrı FPGA deneyleri izlemiştir. Yazılım değerlendirmesinde model tarafından üretilen stator akımları kullanılırken, FPGA deneylerinde kestiricilere aynı kaydedilmiş çalışma aralığındaki ölçülmüş akımlar yeniden oynatılarak uygulanmıştır. Karşılaştırma, kestiricilerin göreli doğruluğunun gürültü düzeyine göre değiştiğini göstermektedir: Kayan kipli filtreler, sınanan koşulların birden fazlasında daha düşük hata elde ederken KB’ye göre daha az mantık kaynağı kullanmıştır. FPGA çıkışları sınanan laboratuvar koşullarında kaydedilmiştir; ancak donanım yerleşimi sonrası zamanlama analizi, belirtilen temel saat kısıtının sağlandığını doğrulamamıştır.

🔖

Cite This Article

Kızmaz, H., Aksoy, S. (2026). Hardware Realization and Resource Analysis of Continuous-Time Sliding Mode State Estimators on FPGA. Balkan Journal of Electrical and Computer Engineering, Volume: 14. https://doi.org/10.17694/bajece.2051336

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (28)

  1. M. G. Aydeniz and İ. Şenol, "A Luenberger-sliding mode observer with rotor time constant parameter estimation in induction motor drives," Turkish Journal of Electrical Engineering & Computer Science, vol. 19, no. 6, p. 901–912, 2011.
  2. M. Ghanes, J. D. Leon and A. Glumineau, "Cascade and high-gain observers comparison for sensorless closed-loop induction motor control," IET Control Theory and Application, vol. 2, no. 2, p. 133–150, 2008.
  3. H. Wang, Y. Yang, X. Ge, Y. Zuo, Y. Yue and S. Li, "PLL- and FLL-Based Speed Estimation Schemes for Speed-Sensorless Control of Induction Motor Drives: Review and New Attempts," IEEE Transactions On Power Electronics, vol. 37, no. 3, p. 3334–3356, March 2022.
  4. E. Zerdali and R. Yildiz, "A study on improving the state estimation of induction motor," Electrical Engineering, vol. 105, p. 2471–2483, 2023.
  5. L. Liu and D. Liu, "Speed and flux observer based on adaptive linear neuron for induction motor," Journal of Power Electronics, vol. 23, p. 1379–1388, 2023.
  6. R. Yildiz, R. Demir and M. Barut, "Online estimations for electrical and mechanical parameters of the induction motor by extended Kalman filter," Transactions of the Institute of Measurement and Control, vol. 45, no. 14, p. 2725−2738, 2023.
  7. G. Yang and T.-H. Chin, "Adaptive-Speed Identification Scheme for a Vector Controlled Speed Sensorless Inverter Induction Motor Drive," IEEE Transactions On Industry Applications, vol. 29, no. 4, p. 820–825, July/August 1993.
  8. C. Schauder, "Adaptive Speed Identification for Vector Control of Induction Motors without Rotational Transducers," IEEE Transactions On Industry Applications, vol. 28, no. 5, p. 1054–1061, September/October 1992.
  9. Y.-R. Kim, S.-K. Sul and M.-H. Park, "Speed Sensorless Vector Control of Induction Motor Using Extended Kalman Filter," IEEE Transactions On Industry Applications, vol. 30, no. 5, p. 1225–1233, September/October 1994.
  10. K. L. Shi, T. F. Chan, Y. K. Wong and S. L. Ho, "Speed Estimation of an Induction Motor Drive Using an Optimized Extended Kalman Filter," IEEE Transactions On Industrial Electronics, vol. 49, no. 1, p. 124–133, February 2002.
  11. J. Holtz, "Sensorless Control of Induction Motor Drives," Proceedings of The IEEE, vol. 90, no. 8, p. 1359–1394, August 2002.
  12. S. Mencou, M. B. Yakhlef and E. B. Tazi, "Advanced control of induction motors (2019–2025): A comprehensive review of strategies, algorithms and sensorless techniques," Advances in Electrical Engineering, Electronics and Energy, no. 101098, 2025.
  13. M. S. Zaky and M. K. Metwaly, "Improved MRAS observer with rotor flux correction terms and FLC-based adaptive law for sensorless induction motor drives," Scientific Reports, vol. 15, no. 14769, 2025.
  14. R. E. Kalman and R. S. Bucy, "New Results in Linear Filtering and Prediction Theory," Journal of Basic Engineering, vol. 83, no. 1, p. 95–108, March 1961.
  15. R. E. Kalman, "A New Approach to Linear Filtering and Prediction Problems," Transactions of the ASME-Journal of Basic Engineering, vol. 82, no. 1, p. 35−45, 1960.
  16. M. Basin and P. Rodriguez-Ramirez, "Sliding Mode Mean-Square Filtering for Linear Stochastic Systems," in IEEE International Conference on Industrial Technology, 2010.
  17. M. V. Basin and P. C. Rodriguez-Ramirez, "Sliding-Mode Filter Design for Linear Systems with Unmeasured States," IEEE Transactions On Industrial Electronics, vol. 58, no. 8, p. 3616–3622, August 2011.
  18. H. Kızmaz, State and parameter estimation of induction motor using neural sliding mode observer, Ph.D. dissertation, Sakarya: Sakarya University, 2015.
  19. H. Kızmaz and S. Aksoy, "State Estimation of Induction Motor via Sliding Mode Filter," in Proceedings of 48th ISERD International Conference, Berlin, 2016.
  20. R. Inan and M. Barut, "Speed-sensorless Direct Vector Control of Induction Motor with the EKF Based stator resistance estimation on FPGA," in 2015 Intl Aegean Conference on Electrical Machines & Power Electronics (ACEMP), 2015 Intl Conference on Optimization of Electrical & Electronic Equipment (OPTIM) & 2015 Intl Symposium on Advanced Electromechanical Motion Systems (ELECTROMOTION), Side, 2015.
  21. S. Y. Maddu and N. R. Bhasme, "Performance Analysis of EKF-based Sensorless Induction Motor Drive using FPGA Controller," in 13th International Symposium on Advanced Topics in Electrical Engineering (ATEE), Bucharest, 2023.
  22. M. Besbes, S. H. Saïd and F. M'Sahli, "FPGA implementation of high gain observer for induction machine using Simulink HDL Coder," in 2015 3rd International Conference on Control, Engineering & Information Technology (CEIT), Tlemcen, 2015.
  23. M. Moutchou, A. Abbou and H. Mahmoudi, "MRAS-based sensorless speed backstepping control for induction machine, using a flux sliding mode observer," Turkish Journal of Electrical Engineering and Computer Sciences, vol. 23, no. 1, p. 187–200, 1 2015.
  24. S. Krim and M. F. Mimouni, "Design and Xilinx Virtex-field-programmable gate array for hardware in the loop of sensorless second-order sliding mode control and model reference adaptive system–sliding mode observer for direct torque control of induction motor drive," Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering, vol. 237, no. 5, 2023.
  25. F. Z. Latrech, A. B. Rhouma and A. Khedher, "FPGA Implementation of DTC-SVM Super-Twisting Sliding Mode Controller with Adaptive Flux Observer for A Double Star Inductıon Motor," Studies in Informatics and Control, vol. 34, no. 4, p. 41–52, 2025.
  26. P. Zhang, J. Wang, Y. Yang, S. Liu and J. Huang, "On Full-Order Flux Observer and Its Discretization for Induction Motor Control," Electronics, vol. 14, no. 5, p. 916, 2025.
  27. M. Basin and P. Rodriguez-Ramirez, "Sliding Mode Mean-Module Filtering for Linear Stochastic Systems," in 2010 IEEE International Conference on Industrial Technology, Via del Mar, 2010.
  28. F. Auger, M. Hilairet, J. M. Guerrero, E. Monmasson, T. Orlowska-Kowalska and S. Katsura, "Industrial Applications of the Kalman Filter: A Review," IEEE Transactions On Industrial Electronics, vol. 60, no. 12, p. 5458–5471, December 2013.