Journals / Politeknik Dergisi / 2026 / Cilt: 29 Sayı: 4

Thermoelectric Energy Conversion Solar Generator Design and Manufacturing

Termoelektrik Enerji Dönüşümüne Sahip Güneş Jeneratörü Tasarımı ve Üretimi

Pages
1–10
Publication Date
2026-06-09
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Experimental results showed that the generator can achieve up to 70 V open-circuit voltage and a peak electrical power output of 23 W under moderate solar irradiance.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Thermoelectric generators (TEGs) are gaining increasing attention as a promising solution for renewable energy production and waste heat recovery.
📊
Key Findings & Data:This study presents the design, fabrication, and performance evaluation of a novel thermoelectric solar generator that integrates 30 TEG modules with standard evacuated glass tubes for solar heating and a chimney-type wind-assisted passive cooling mechanism.
💡
Conclusion & Impact:Experimental results showed that the generator can achieve up to 70 V open-circuit voltage and a peak electrical power output of 23 W under moderate solar irradiance.
🔬Design:Araştırma Makalesi
📍Scope:Comprehensive Sample
⚙️Variables:Termoelektrik jeneratör · güneş enerjisi · yenilenebilir enerji

Abstract

Thermoelectric generators (TEGs) are gaining increasing attention as a promising solution for renewable energy production and waste heat recovery. This study presents the design, fabrication, and performance evaluation of a novel thermoelectric solar generator that integrates 30 TEG modules with standard evacuated glass tubes for solar heating and a chimney-type wind-assisted passive cooling mechanism. The proposed system operates entirely without external energy input, relying on natural thermal gradients to produce electricity. Experimental results showed that the generator can achieve up to 70 V open-circuit voltage and a peak electrical power output of 23 W under moderate solar irradiance. The overall energy conversion efficiency was calculated to be 8.28%, demonstrating the viability of thermoelectric-only systems as an alternative to conventional photovoltaic or hybrid PV-TEG configurations. The system's scalability, autonomy, and dual potential for heat and power generation suggest strong applicability in off-grid and remote energy solutions.

Özet

Termoelektrik jeneratörler (TEG'ler), yenilenebilir enerji üretimi ve atık ısı geri kazanımı için umut vadeden bir çözüm olarak giderek daha fazla ilgi görmektedir. Bu çalışma, güneş enerjisiyle ısıtma için standart vakumlu cam tüpler ve baca tipi rüzgar destekli pasif soğutma mekanizması ile 30 TEG modülünü entegre eden yeni bir termoelektrik güneş jeneratörünün tasarımını, üretimini ve performans değerlendirmesini sunmaktadır. Önerilen sistem, elektrik üretmek için doğal termal gradyanlara dayanarak, tamamen harici enerji girdisi olmadan çalışmaktadır. Deneysel sonuçlar, jeneratörün orta düzeyde güneş ışınımı altında 70 V'a kadar açık devre voltajı ve 23 W'lık tepe elektrik gücü çıkışı elde edebildiğini göstermiştir. Genel enerji dönüşüm verimliliği %8,28 olarak hesaplanmış olup, termoelektrik sistemlerin geleneksel fotovoltaik veya hibrit PV-TEG konfigürasyonlarına alternatif olarak uygulanabilirliğini göstermektedir. Sistemin ölçeklenebilirliği, özerkliği ve ısı ve güç üretimi için ikili potansiyeli, şebeke dışı ve uzak enerji çözümlerinde güçlü bir uygulanabilirlik önermektedir.

🔖

Cite This Article

Özdemir, A. E., Oy, S. A. (2026). Thermoelectric Energy Conversion Solar Generator Design and Manufacturing. Politeknik Dergisi, Cilt: 29 Sayı: 4, 1–10. https://doi.org/10.2339/politeknik.1656289

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (43)

  1. S. Lineykin and S. Ben-Yaakov, "Modeling and analysis of thermoelectric modules," IEEE Transactions on Industry Applications, 43(2):505-512, (2007).
  2. I. Laird and D. D.-C. Lu, "High step-up DC/DC topology and MPPT algorithm for use with a thermoelectric generator," IEEE Transactions on Power Electronics, 28(7):3147-3157, (2013).
  3. N. Fuschillo, R. Gibson, F. K. Eggleston and J. Epstein, "Theory and performance of flat plate solar thermoelectric generator for near-earth orbits," IEEE Transactions on Aerospace, AS-3(2):652-663, (1965).
  4. F. K. Eggleston and N. Fuschillo, "Fabrication of flat plate solar thermoelectric generator panels for near-earth orbits," IEEE Transactions on Aerospace, 2(2):674-680, (1965).
  5. G. W. Glassburn, "Flat plate solar thermoelectric generator orbital experiment," IEEE Transactions on Aerospace-Support Conference Procedures, 1(2):1396-1403, (1963).
  6. G. J. Snyder, "Small thermoelectric generators," The Electrochemical Society Interface, 54-56, (2008).
  7. https://solarsystem.nasa.gov/rps/docs/MMRTG%20Fact%20Sheet%20update%2010-2-13.pdf (2.12.2017).
  8. Y. Hsiao, W. Chang and S. Chen, "A mathematic model of thermoelectric module with applications on waste heat recovery from automobile engine," Energy, 35:1447-1454, (2010).
  9. C.-C. Weng and M.-J. Huang, "A simulation study of automotive waste heat recovery using a thermoelectric power generator," International Journal of Thermal Sciences, 71:302-309, (2013).
  10. D.-J. Yao, K.-J. Yeh, C.-T. Hsu, B.-M. Yu and J.-S. Lee, "A thermoelectric power generator for automobiles," IEEE Nanotechnology Magazine, 28-33, (2009).
  11. R. Nuwayhid and R. Hamade, "Design and testing of a locally made loop-type thermosyphonic heat sink for stove-top thermoelectric generators," Renewable Energy, 30:1101-1116, (2005).
  12. P.-S. Weng, H.-Y. Tang, P.-C. Ku and L.-H. Lu, "50 mV-input batteryless boost converter for thermal energy harvesting," IEEE Journal of Solid-State Circuits, 48(4):1031-1041, (2013).
  13. S. Karabetoglu, A. Sisman and Z. F. Ozturk, "Characterization of a thermoelectric generator at low temperatures," Energy Conversion and Management, 62:47-50, (2012).
  14. M. Chen, L. A. Rosendahl and C. Thomas, "A three-dimensional numerical model of thermoelectric generators in fluid power systems," International Journal of Heat and Mass Transfer, 54:345-355, (2011).
  15. F. Felgner, L. Exel, M. Nesarajah and G. Frey, "Component-oriented modeling of thermoelectric devices for energy system design," IEEE Transactions on Industrial Electronics, 61(3):1301-1310, (2014).
  16. F. J. Lesage, R. Pelletier, L. Fournier and É. V. Sempels, "Optimal electrical load for peak power of a thermoelectric module with a solar electric application," Energy Conversion and Management, 74:51-59, (2013).
  17. N. Miljkovic and E. N. Wang, "Modeling and optimization of hybrid solar thermoelectric systems with thermosyphons," Solar Energy, 85(11):2843-2855, (2011).
  18. J. Xiao, T. Yang, P. Li, P. Zhai and Q. Zhang, "Thermal design and management for performance optimization of solar thermoelectric generator," Applied Energy, 93:33-38, (2012).
  19. Y. Li, K. Buddharaju, N. Singh, G. Q. Lo and S. J. Lee, "Chip-level thermoelectric power generators based on high-density silicon nanowire array prepared with top-down CMOS technology," IEEE Electron Device Letters, 32(5):674-676, (2011).
  20. R. Singh, S. Tundee and A. Akbarzadeh, "Electric power generation from solar pond using combined thermosyphon and thermoelectric modules," Solar Energy, 85(2):371-378, (2011).
  21. P. M. Cuce, T. Guclu and E. Cuce, "Design, modelling, environmental, economic and performance analysis of parabolic trough solar collector (PTC) based cogeneration systems assisted by thermoelectric generators (TEGs)," Sustainable Energy Technologies and Assessments, 64, (2024).
  22. A. Banakar, A. Motevali, M. Emad and B. Ghobadian, "Co-generation of heat and power in a thermoelectric system equipped with Fresnel lens collectors using active and passive cooling techniques," Renewable Energy, 112:268-279, (2017).
  23. A. Date, A. Date, C. Dixon and A. Akbarzadeh, "Theoretical and experimental study on heat pipe cooled thermoelectric generators with water heating using concentrated solar thermal energy," Solar Energy, 105:656-668, (2014).
  24. X. F. Zheng, C. X. Liu, R. Boukhanouf, Y. Y. Yan and W. Z. Li, "Experimental study of a domestic thermoelectric cogeneration system," Applied Thermal Engineering, 62(1):69-79, (2014).
  25. L. Miao, M. Zhang, S. Tanemura, T. Tanaka, Y. P. Kang and G. Xu, "Feasibility study on the use of a solar thermoelectric cogenerator comprising a thermoelectric module and evacuated tubular collector with parabolic trough concentrator," Journal of Electronic Materials, 41(6):1759-1765, (2012).
  26. C. Li, M. Zhang, L. Miao, J. Zhou, Y. P. Kang, C. A. J. Fisher, K. Ohno, Y. Shen and H. Lin, "Effects of environmental factors on the conversion efficiency of solar thermoelectric co-generators comprising parabola trough collectors and thermoelectric modules without evacuated tubular collector," Energy Conversion and Management, 86:944-951, (2014).
  27. L. Miao, Y. P. Kang, C. Li, S. Tanemura, C. L. Wan, Y. Iwamoto, Y. Shen and H. Lin, "Experimental performance of a solar thermoelectric cogenerator comprising thermoelectric modules and parabolic trough concentrator without evacuated tube," Journal of Electronic Materials, 44(6):1972-1983, (2015).
  28. B. Ohara, M. Wagner, C. Kunkle, P. Watson, R. Williams, R. Donohoe, K. Ugarte, R. Wilmoth, M. Z. Chong and H. Lee, "Residential solar combined heat and power generation using solar thermoelectric generation," Journal of Electronic Materials, 44(6):2132-2141, (2015).
  29. M. Zhang, L. Miao, Y. P. Kang, S. Tanemura, C. A. J. Fisher, G. Xu, C. X. Li and G. Z. Fan, "Efficient, low-cost solar thermoelectric cogenerators comprising evacuated tubular solar collectors and thermoelectric modules," Applied Energy, 109:51-59, (2013).
  30. D. Kraemer, K. McEnaney, M. Chiesa and G. Chen, "Modeling and optimization of solar thermoelectric generators for terrestrial applications," Solar Energy, 86(5):1338-1350, (2012).
  31. E. A. Chávez-Urbiola, Y. V. Vorobiev and L. P. Bulat, "Solar hybrid systems with thermoelectric generators," Solar Energy, 86(1):369-378, (2012).
  32. Y. Deng, W. Zhu, Y. Wang and Y. Shi, "Enhanced performance of solar-driven photovoltaic–thermoelectric hybrid system in an integrated design," Solar Energy, 88:182-191, (2013).
  33. Y. Li, S. Witharana, H. Cao, M. Lasfargues, Y. Huang and Y. Ding, "Wide spectrum solar energy harvesting through an integrated photovoltaic and thermoelectric system," Particuology, 15:39-44, (2014).
  34. T. Cui, Y. Xuan and Q. Li, "Design of a novel concentrating photovoltaic–thermoelectric system incorporated with phase change materials," Energy Conversion and Management, 112:49-60, (2016).
  35. D. N. Kossyvakis, G. D. Voutsinas and E. V. Hristoforou, "Experimental analysis and performance evaluation of a tandem photovoltaic–thermoelectric hybrid system," Energy Conversion and Management, 117:490-500, (2016).
  36. M. Mohsenzadeh, M. B. Shafii and H. Jafari Mosleh, "A novel concentrating photovoltaic/thermal solar system combined with thermoelectric module in an integrated design," Renewable Energy, 113:822-834, (2017).
  37. T. Liao, B. Lin and Z. Yang, "Performance characteristics of a low concentrated photovoltaic–thermoelectric hybrid power generation device," International Journal of Thermal Sciences, 77:158-164, (2014).
  38. E. Elsarrag, H. Pernau, J. Heuer, N. Roshan, Y. Alhorr and K. Bartholomé, "Spectrum splitting for efficient utilization of solar radiation: a novel photovoltaic–thermoelectric power generation system," Renewables: Wind, Water, and Solar, 2(1):1-11, (2015).
  39. R. Bjørk and K. K. Nielsen, "The performance of a combined solar photovoltaic (PV) and thermoelectric generator (TEG) system," Solar Energy, 120:187-194, (2015).
  40. J. M. Carrasco, L. G. Franquelo, J. T. Bialasiewicz, E. Galvan, R. C. P. Guisado, M. A. M. Prats, J. I. Leon and N. Moreno-Alfonso, "Power-electronic systems for the grid integration of renewable energy sources: a survey," IEEE Transactions on Industrial Electronics, 53(4):1002-1016, (2006).
  41. W. Deng, F. Liu and H. Jin, "Harnessing renewable energy in cloud datacenters: opportunities and challenges," IEEE Network, 48-55, (2014).
  42. R. H. Inman, H. T. C. Pedro and C. F. M. Coimbra, "Solar forecasting methods for renewable energy integration," Progress in Energy and Combustion Science, 39(6):535-576, (2013).
  43. D. Mastbergen, "Development and optimization of a stove-powered thermoelectric generator," Doctoral Thesis, Colorado State University, Fort Collins, CO, (2008).