SavedAdd your journal

Journals / Challenge Journal of Concrete Research Letters / 2017 / Cilt: 8 - Sayı: 2

Effectiveness of high performance mortar reinforced with fibers as a repair material

Eethar Thanon DAWOOD
Tamara Waleed GANIM
Pages
29–47
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results indicate that the hybridization of 1.8% steel fibers and 0.2% polypropylene fibers is very beneficial to decrease the production cost of fiber reinforced mortar for large scale construction project applications.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The present work deals with engineering properties of high performance mortar (HPM) to be used as a repair material.
📊
Key Findings & Data:The results indicate that the hybridization of 1.8% steel fibers and 0.2% polypropylene fibers is very beneficial to decrease the production cost of fiber reinforced mortar for large scale construction project applications.
💡
Conclusion & Impact:On the other hand, in three parts bonding, the combined system of NC with epoxy has the best bond strength while HPM reinforced fibers show a better failure mode.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Özet

The present work deals with engineering properties of high performance mortar (HPM) to be used as a repair material. The experimental study was conducted on HPM reinforced with mono steel fibers and hybrid fibers consist of steel and polypropylene fibers. The economical efficiency of the designed mono and hybrid fibers reinforced mortar were presented. The results indicate that the hybridization of 1.8% steel fibers and 0.2% polypropylene fibers is very beneficial to decrease the production cost of fiber reinforced mortar for large scale construction project applications. The combined system of substrate concrete with different mixes of HPM was used to study its bond strength properties. The experimental tests are: two-part bond strength tests in additional to three part-bond strength tests. It was found that HPM reinforced by hybrid fibers has the best performance when two-part bond strength is required. On the other hand, in three parts bonding, the combined system of NC with epoxy has the best bond strength while HPM reinforced fibers show a better failure mode.

🔖

Cite This Article

DAWOOD, E. T., GANIM, T. W. (2017). Effectiveness of high performance mortar reinforced with fibers as a repair material. Challenge Journal of Concrete Research Letters, Cilt: 8 - Sayı: 2, 29–47. https://ajindex.com/articles/143865

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (7)

  1. Abd ElAty MA (2013). Influence of bending deflection rate on properties of fibrous mortar. HBRC Journal, 9, 27–35. ASTM C1018 (2002). Standard Test Method for Flexural Toughness and First-Crack Strength of Fiber-Reinforced Concrete (Using Beam with Third-Point Loading). Annual book of ASTM Standards. ASTM C109 (2002). Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens). Annual book of ASTM Standards. ASTM C230 (2002). Standard Specification for Flow Table for Use in Tests of Hydraulic Cement. Annual book of ASTM Standards. ASTM C348 (2002). Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars. Annual book of ASTM Standards. ASTM C496 (2002). Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens. Annual book of ASTM Standards. ASTM C642 (2002).
  2. Standard Test Method for Density, Absorption, and Voids in Hardened Concrete. Annual book of ASTM Standards. ASTM C78 (2002). Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading). Annual book of ASTM Standards. ASTM C882 (2002). Standard Test Method for Bond Strength of EpoxyResin Systems Used With Concrete by Slant Shear. Annual book of ASTM Standards. Aydin A (2007). Self compactability of high volume hybrid fiber reinforced concrete. Construction and Building Materials, 21(6), 1149- 1154. Balaguru PN, Shah SP (1992). Fiber-Reinforced Cement Composites. McGraw-Hill Inc., New York. Balendran R, Zhou F, Nadeem A, leung AYT (2002). Influence of steel fibres on strength and ductility of normal and lightweight high strength concrete. Building and Environment, 37, 1361-1367.
  3. Banthia N, Sappakittipakorn M (2007). Toughness enhancement in steel fiber reinforced concrete through fiber hybridization. Cement and Concrete Research, 37(9), 1366-1372.
  4. Bendjillalia K, Gouala MS, Chemrouk M, Damenea Z (2011). Study of the reinforcement of limestone mortars by polypropylene fibers waste. Physics Procedia, 21, 42–46.
  5. Bentur A, Mindess S (1990). Fiber Reinforced Cementitious Composites. Elsevier Applied Science, London. Campello E, Pereira MV, Darwisha F (2014). The effect of short metallic and polymeric fiber on the fracture behavior of cement mortar. Procedia Materials Science, 3, 1914–1921.
  6. Chan YW, Chu SH (2004). Effect of silica fume on steel fiber bond characteristics in reactive powder concrete. Cement and Concrete Research, 34(7), 1167–1172.
  7. Chynoweth G, Stankie RR, All