SavedAdd your journal

Journals / Bitlis Eren Üniversitesi Fen Bilimleri Dergisi / 2026 / Volume: 15 Issue: 2

Shear-Dominated Bending Response of CFRP/Al Sandwich Joints: Influence of Stacking Sequence, Hybrid Bonding and PAN Nanofiber Interleaves

Hasan Ulus(SELCUK UNIVERSITY)0000-0001-8591-8993
Pages
—
Publication Date
2026-06-30
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The best-performing nanofiber-interleaved hybrid reached 6789 N (A–C–A) and 8406 N (C–A–C), about 52% and 90% above bolt-only, respectively, highlighting a robust route to simultaneous gains in strength, energy absorption, and damage tolerance.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Fiber–metal laminates (FMLs) that pair aluminum with CFRP offer an appealing balance of low weight and damage tolerance, yet their structural efficiency often depends on how well the composite–metal joints are designed.
📊
Key Findings & Data:Nanofiber interleaves did not push bonded joints beyond the bolt-only peak-load level, but they markedly increased energy absorption and shifted failure from mainly adhesive debonding to mixed adhesive/cohesive fracture.
💡
Conclusion & Impact:The best-performing nanofiber-interleaved hybrid reached 6789 N (A–C–A) and 8406 N (C–A–C), about 52% and 90% above bolt-only, respectively, highlighting a robust route to simultaneous gains in strength, energy absorption, and damage tolerance.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Fiber–Metal Laminates · CFRP/Al2024 · Hybrid Bonded–Bolted Joints

Abstract

Fiber–metal laminates (FMLs) that pair aluminum with CFRP offer an appealing balance of low weight and damage tolerance, yet their structural efficiency often depends on how well the composite–metal joints are designed. Here, we examine the shear-dominated flexural response of Al/CFRP sandwich joints and quantify how (i) stacking sequence and (ii) PAN nanofiber-interleaved toughening influence strength, energy absorption, and failure mode. Two laminate architectures were studied: Al–CFRP–Al (A–C–A) and CFRP–Al–CFRP (C–A–C). For each architecture, five joint concepts were produced using a structural epoxy: bolt-only (reference), neat bonded, PAN nanofiber-interleaved bonded, neat bonded/bolted hybrid, and nanofiber-bonded/bolted hybrid. Short-span three-point bending was selected to emphasize interlaminar and bondline shear, and load–displacement curves were used to extract maximum load, apparent interlaminar shear strength, total failure energy, and energy to maximum load, supported by post-failure observations. Nanofiber interleaves did not push bonded joints beyond the bolt-only peak-load level, but they markedly increased energy absorption and shifted failure from mainly adhesive debonding to mixed adhesive/cohesive fracture. Hybrid joints consistently outperformed both bonded and bolted configurations; with PAN toughening, nano-hybrid joints showed the highest loads and the most progressive, non-catastrophic response. Switching from A–C–A to C–A–C further enhanced strength and energy, especially for hybrids. The best-performing nanofiber-interleaved hybrid reached 6789 N (A–C–A) and 8406 N (C–A–C), about 52% and 90% above bolt-only, respectively, highlighting a robust route to simultaneous gains in strength, energy absorption, and damage tolerance.

🔖

Cite This Article

Ulus, H. (2026). Shear-Dominated Bending Response of CFRP/Al Sandwich Joints: Influence of Stacking Sequence, Hybrid Bonding and PAN Nanofiber Interleaves. Bitlis Eren Üniversitesi Fen Bilimleri Dergisi, Volume: 15 Issue: 2. https://doi.org/10.17798/bitlisfen.1834444

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (42)

  1. I. Uygur, A. Cicek, E. Toklu, R. Kara, and S. Saridemir, "Fatigue life predictions of metal matrix composites using artificial neural networks," Archives of Metallurgy and Materials, vol. 59, no. 1, pp. 97-103, 2014.
  2. I. Uygur, "Influence of PartIcle SIzeS and Volume fractIonS on fatIgue crack growth rateS of aeroSPace al-alloyS comPoSIteS," Archives of Metallurgy and Materials, vol. 69, no. 1, pp. 337-341, 2024.
  3. I. Uygur, "Environmentally assisted fatigue response of Al-Cu-Mg-Mn with SiC particulate metal matrix composites," University of Wales Swansea, 1999.
  4. İ. U. Uygur and H. Saruhan, "ALUMiNYUM ESASLI METAL MATRİS KOMPOZiT MALZEMELERiN MEKANİK ÖZELLİKLERİ•," Sakarya University Journal of Science, vol. 8, no. 1, pp. 167-174, 2004.
  5. B. N. Bhat et al., "Aerospace materials characteristics," American Institute of Aeronautics and Astronautics, 2018.
  6. M. Vijayan, V. Selladurai, G. Balaganesan, and G. Suganya Priyadharshini, "Comprehensive characterization of AA 2024T3 fiber metal laminate with nanosilica‐reinforced epoxy based polymeric composite panel for lightweight applications," Polymer Composites, vol. 43, no. 11, pp. 8274-8296, 2022.
  7. W. X. Wang, Y. Takao, and T. Matsubara, "Galvanic corrosion-resistant carbon fiber metal laminates," in 16th International Conference on Composite Materials, ICCM-16-" A Giant Step Towards Environmental Awareness: From Green Composites to Aerospace", 2007.
  8. H. E. Etri, M. E. Korkmaz, M. K. Gupta, M. Gunay, and J. Xu, "A state-of-the-art review on mechanical characteristics of different fiber metal laminates for aerospace and structural applications," The International Journal of Advanced Manufacturing Technology, vol. 123, no. 9, pp. 2965-2991, 2022.
  9. M. Caggiano, M. R. Saffioti, and G. Rotella, "Fiber Metal Laminates: The Role of the Metal Surface and Sustainability Aspects," Journal of Composites Science, vol. 9, no. 1, p. 35, 2025.
  10. I. El-Sagheer, A. A. Abd-Elhady, and H. E.-D. M. Sallam, "Quasistatic tensile and flexural behaviors of fiber metal laminates after subjecting to uniaxial tensile impact loading," Scientific Reports, vol. 15, no. 1, p. 16051, 2025.
  11. J. Wang, T. Qiao, A. Wang, X. Li, and T. Wang, "Mechanism of Interlaminar Strengthening and Toughening of Al/CFRP/Al Composite Laminates," Materials, vol. 16, no. 2, p. 560, 2023.
  12. S. Maggiore, M. Banea, P. Stagnaro, and G. Luciano, "A review of structural adhesive joints in hybrid joining processes. Polymers 13 (22): 3961," ed, 2021.
  13. L. Yan, R. Jiang, and Y. Zuo, "Damage Analysis of CFRP Hybrid Bonded-Bolted Joint during Insertion of Interference-Fit Bolt," Materials, vol. 16, no. 10, p. 3753, 2023.
  14. M. Damghani, M. S. Khan, and G. A. Atkinson, "Experimental study of bonded, bolted, and hybrid bonded-bolted single lap shear joints with woven CFRP adherends," Composite Structures, vol. 334, p. 117989, 2024.
  15. D. Perfetto, A. Polverino, A. Aversano, and A. De Luca, "FE Analyses of a CFRP–Aluminum Single‐Lap Hybrid Bonded/Bolted Joint at Different Tensile Loads," in Macromolecular Symposia, 2023, vol. 411, no. 1: Wiley Online Library, p. 2300015.
  16. B. Luo, L. Xue, Q. Wang, and P. Zou, "Mechanistic study of Failure in CFRP hybrid bonded–bolted interference connection structures under tensile loading," Materials, vol. 17, no. 9, p. 2117, 2024.
  17. F. Delzendehrooy, A. Akhavan-Safar, A. Barbosa, R. Carbas, E. Marques, and L. Da Silva, "Investigation of the mechanical performance of hybrid bolted-bonded joints subjected to different ageing conditions: Effect of geometrical parameters and bolt size," Journal of Advanced Joining Processes, vol. 5, p. 100098, 2022.
  18. W. Mu, S. Zhang, S. Li, L. Chen, and H. Chen, "Experimental and numerical investigation on the tensile performances of bonded/bolted hybrid CFRP‐AL joints," Polymer Composites, 2025.
  19. R. Gopalan and P. Narayanan, "Experimental and numerical investigation of tensile-loaded staggered bolted and hybrid pultruded composite double lap joints," Journal of Adhesion Science and Technology, vol. 38, no. 11, pp. 1895-1924, 2024.
  20. B. Mahato, S. V. Lomov, A. Shiverskii, M. Owais, and S. G. Abaimov, "A review of electrospun nanofiber interleaves for interlaminar toughening of composite laminates," Polymers, vol. 15, no. 6, p. 1380, 2023.
  21. M. Ekrem and A. Avcı, "Effects of polyvinyl alcohol nanofiber mats on the adhesion strength and fracture toughness of epoxy adhesive joints," Composites Part B: Engineering, vol. 138, pp. 256-264, 2018.
  22. F. Zhu, L. Ke, Z. Feng, J. Zhou, C. Li, and R. Zhang, "Enhancing bond performance of CFRP-steel epoxy-bonded interface by electrospun nanofiber veils," Thin-Walled Structures, vol. 198, p. 111765, 2024.
  23. F. Musiari et al., "Feasibility study of adhesive bonding reinforcement by electrospun nanofibers," Procedia Structural Integrity, vol. 2, pp. 112-119, 2016.
  24. M. T. Tınastepe, H. B. Kaybal, H. Ulus, M. O. Erdal, M. E. Cetin, and A. Avcı, "Quasi-Static tensile loading performance of Bonded, Bolted, and hybrid Bonded-Bolted Carbon-to-Carbon composite Joints: Effect of recycled polystyrene nanofiber interleaving," Composite Structures, vol. 323, p. 117445, 2023.
  25. M. Dündar, İ. Uygur, and E. Ekici, "Optimization of low-velocity impact behavior of FML structures at different environmental temperatures using taguchi method and grey relational analysis," Journal of Composite Materials, vol. 59, no. 7, pp. 885-906, 2025.
  26. M. Dündar, İ. Uygur, E. Ekici, C. Taşçıoğlu, and B. Gülenç, "Numerical and Statistical İnvestigation Of The Effect Of Composite Layer Thickness On Low-Velocity İmpact Behaviour in Fibre Metal Laminate Materials," Politeknik Dergisi, pp. 1-1.
  27. J. Sun, X. Zhou, X. Wei, Y. Liu, and J. Zhang, "Study on bending properties and damage mechanism of carbon fiber reinforced aluminum laminates," Matéria (Rio de Janeiro), vol. 29, no. 3, p. e20240310, 2024.
  28. H. Mou, Y. Chen, Z. Feng, and H. Liu, "Damage and energy absorption behavior of CFRP/aluminum hybrid open-section thin-walled columns subjected to quasi-static loading," Thin-Walled Structures, vol. 197, p. 111593, 2024.
  29. R. J. Carbas, M. P. Palmares, and L. F. da Silva, "Experimental and FE study of hybrid laminates aluminium carbon-fibre joints with different lay-up configurations," Manufacturing Review, vol. 7, p. 2, 2020.
  30. J. Bieniaś, P. Jakubczak, M. Droździel, and B. Surowska, "Interlaminar shear strength and failure analysis of aluminium-carbon laminates with a glass fiber interlayer after moisture absorption," Materials, vol. 13, no. 13, p. 2999, 2020.
  31. B. Surowska, K. Dadej, P. Jakubczak, and J. Bieniaś, "Short-beam shear fatigue life assessment of thermally cycled carbon–aluminium laminates with protective glass interlayers," Archives of Civil and Mechanical Engineering, vol. 21, no. 2, p. 50, 2021.
  32. M. Y. Khalid et al., "Interlaminar shear strength (ILSS) characterization of fiber metal laminates (FMLs) manufactured through VARTM process," Forces in Mechanics, vol. 4, p. 100038, 2021.
  33. H. Ulus, "The impact of seawater aging on basalt/graphene nanoplatelet-epoxy composites: performance evaluating by Dynamic Mechanical Analysis (DMA) and short beam shear (sbs) tests," Niğde Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi, vol. 10, no. 1, pp. 412-419, 2021.
  34. A. B. Abdul Raheman, K. Bilge, and M. Papila, "Effects of Nanofiber Interleaving on the Strength and Failure Behavior of Co-Cured Composite Joints with Fiber Orientation Mismatch," Journal of Composites Science, vol. 9, no. 6, p. 285, 2025.
  35. G. Esenoglu et al., "Investigating the effects of pa66 electrospun nanofibers layered within an adhesive composite joint fabricated under autoclave curing," ACS omega, vol. 8, no. 36, pp. 32656-32666, 2023.
  36. H. B. Kaybal and H. Ulus, "Comparative analysis of thermoplastic and thermoset adhesives performance and the influence on failure analysis in jointed elium‐based composite structures," Polymer Composites, vol. 45, no. 4, pp. 3474-3492, 2024.
  37. M. T. Tınastepe, H. B. Kaybal, H. Ulus, M. O. Erdal, M. E. Çetin, and A. Avcı, "Quasi-Static tensile loading performance of Bonded, Bolted, and hybrid Bonded-Bolted Carbon-to-Carbon composite Joints: Effect of recycled polystyrene nanofiber interleaving," Composite Structures, vol. 323, p. 117445, 2023.
  38. S. Gao, W. Hou, J. Xing, and L. Sang, "Numerical and experimental investigation of flexural properties and damage behavior of CFRTP/Al laminates with different stacking sequence," Applied Sciences, vol. 13, no. 3, p. 1667, 2023.
  39. H. Ulus and H. B. Kaybal, "Out-of-plane static loading performance of lightweight aluminum/composite FML structures for retrofitting applications: Effectiveness of bonded, bolted and hybrid bonded/bolted joining techniques under hydrothermal aging environment," Construction and Building Materials, vol. 403, p. 133124, 2023.
  40. J. S. M. Zanjani, B. Beylergil, L. H. Poudeh, B. Alkhateab, Y. Menceloglu, and M. Yildiz, "Effect of nanomaterials/nanofibers on the structure and properties of fiber-reinforced composites," in Fiber-reinforced nanocomposites: fundamentals and applications: Elsevier, 2020, pp. 157-182.
  41. M. A. Şenyurt, M. M. Kurdiş, H. Ulus, and A. Avcı, "Enhanced Mechanical and Shape Memory Properties of Elium® Nanocomposites Reinforced with Graphene and Iron (II, III) Oxide-Doped Polyacrylonitrile Nanofibers," Fibers and Polymers, vol. 26, no. 5, pp. 2097-2116, 2025.
  42. B. Beylergil, M. Tanoğlu, and E. Aktaş, "Modification of carbon fibre/epoxy composites by polyvinyl alcohol (PVA) based electrospun nanofibres," Advanced Composites Letters, vol. 25, no. 3, p. 096369351602500303, 2016.