Journals / Politeknik Dergisi / 2005 / Cilt: 8 Sayı: 4

Investigation of the Effect of Cutting Tool Rake Angle on Feed Force

Kesici Takım Talaş Açısının İlerleme Kuvveti Üzerindeki Etkisinin Araştırılması

Pages
323–328
Publication Date
2005-12-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Theoretically calculated and experimentally obtained Ffratio was found to be mean 0.69

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This paper presents a study of investigation into cutting tool rake angle effect on feed force to have secondary important during machining.
📊
Key Findings & Data:AISI 1040 was used as the workpiece material.
💡
Conclusion & Impact:Theoretically calculated and experimentally obtained Ffratio was found to be mean 0.69
🔬Design:Makale
📍Scope:Comprehensive Sample
⚙️Variables:Talaş Açısı · İlerleme Kuvveti · Dinamometre

Abstract

This paper presents a study of investigation into cutting tool rake angle effect on feed force to have secondary important during machining. For this purpose, a dynamometer was designed and manufactured for experimental determination of the cutting forces and mounted to a CNC turning centre. With the help of two beam type load cells suitably located on the dynamometer, it became possible to sense the cutting tool deflections due to the cutting forces. AISI 1040 was used as the workpiece material. Cutting forces (Fcand Ff) were measured with eight different rake angles changing from negative to positive values at five different cutting speeds. For all the tests, dept of cut and feed rate were kept constant. In addition, theoretically calculated feed force results were compared with the experimentally obtained ones. The lowest feed force (Ff) was observed when the rake angle was zero degree. Theoretically calculated and experimentally obtained Ffratio was found to be mean 0.69

Özet

Takım talaş açısının, talaş kaldırma sürecinde oluşan kesme kuvvetleri açısından ikinci derecede öneme sahip olan ilerleme kuvveti üzerindeki etkisinin değerlendirilmesi amacıyla yapılan bu çalışmada, kesme kuvvetlerinin (Fc ve Ff) deneysel olarak belirlenebilmesi için Bilgisayarlı Sayısal Denetimli (BSD) torna tezgahına bağlanabilen bir dinamometre tasarımı ve imalatı gerçekleştirilmiştir. Dinamometre üzerinde bulunan 2 adet kiriş tipi yük hücresi yardımıyla kesici takımda kesme kuvvetleriyle oluşan yer değiştirmelerin sezilebilmesi mümkün olmuştur. Deneysel çalışmalarda, AISI 1040 çelik malzeme kullanılarak, 5 farklı kesme hızında, ilerleme ve talaş derinliği sabit tutularak, negatiften pozitife doğru 8 farklı talaş açısı için kesme kuvvetleri belirlenmiştir. Ayrıca, teorik olarak hesaplanan ilerleme kuvvetleri ile deneysel olarak elde edilen değerler karşılaştırılmıştır. Yapılan değerlendirme sonucunda, ilerleme kuvvetinin (Ff) 00’lik talaş açısında en küçük değerine ulaştığı gözlenmiştir. Deneysel ve teorik olarak elde edilen ilerleme kuvvetleri arasında ortalama 0.69 gibi bir oran tespit edilmiştir.

🔖

Cite This Article

Günay, M., Şeker, U. (2005). Investigation of the Effect of Cutting Tool Rake Angle on Feed Force. Politeknik Dergisi, Cilt: 8 Sayı: 4, 323–328. https://ajindex.com/articles/1303195

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...