SavedAdd your journal

Journals / Gazi University Journal of Science / 2026 / Volume: 32 Issue: 1

Determination of Optimum Rotational Speed of the Heat Wheel through Computational Fluid Dynamics Simulation

Adnan Sozen
Erdem Cıftcı0000-0003-2493-5962
Pages
—
Publication Date
2019-03-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Consequently, it has been observed that they are in good agreement each other.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Heat wheel is a kind of regenerative heat exchanger mostly used in Heating, Ventilation and Air Conditioning (HVAC) systems for two main goals; energy recovery from the waste heat and /or dehumidification of the air.
📊
Key Findings & Data:Performance of the heat wheel utilized merely for energy recovery has been numerically investigated in this study.
💡
Conclusion & Impact:Consequently, it has been observed that they are in good agreement each other.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Heat wheel · Energy recovery · Performance

Abstract

Heat wheel is a kind of regenerative heat exchanger mostly used in Heating, Ventilation and Air Conditioning (HVAC) systems for two main goals; energy recovery from the waste heat and /or dehumidification of the air. Performance of the heat wheel utilized merely for energy recovery has been numerically investigated in this study. For the aim of determining the optimum rotational speed, three different angular velocities have been used under the transient conditions. The findings obtained from the analysis have been compared to a validated experimental study in literature. Consequently, it has been observed that they are in good agreement each other.

🔖

Cite This Article

Sozen, A., Cıftcı, E. (2019). Determination of Optimum Rotational Speed of the Heat Wheel through Computational Fluid Dynamics Simulation. Gazi University Journal of Science, Volume: 32 Issue: 1. https://ajindex.com/articles/1269209

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (21)

  1. Zhang, L. Z. and Niu, J. L., “A numerical study of laminar forced convection in sinusoidal ducts with arc lower boundaries under uniform wall temperature”, Num. Heat Trans. Part A: An Int. J. Comp. Method., 40(1): 55-72, (2010). http://dx.doi.org/10.1080/10407780117998
  2. Sphaier, L. A. and Worek, W. M., “The effect of axial diffusion in desiccant and enthalpy wheels”, Int. J. Heat Mass Trans., 49(7-8): 1412-1419, (2005). https://doi.org/10.1016/j.ijheatmasstransfer.2005.09.035
  3. Ruivo, C. R., Costa, J. J. and Figueiredo, A. R., “Numerical study of the influence of the atmospheric pressure on the heat and mass transfer rates of desiccant wheels”, Int. J. Heat Mass Trans., 54(7-8): 1331-1339, (2011). https://doi.org/10.1016/j.ijheatmasstransfer.2010.12.008
  4. Tu, R., Liu, X. H. and Jiang, Y., “Performance comparison between enthalpy recovery wheels and dehumidification wheels”, Int. J. Refri., 36(8): 2308-2322, (2013). https://doi.org/10.1016/j.ijrefrig.2013.07.014
  5. Wu, Z., Melnik, R. V. N. and Borup, F., “Model-based analysis and simulation of regenerative heat wheel”, Energy and Build., 38(5): 502-514, (2005). https://doi.org/10.1016/j.enbuild.2005.08.009
  6. Niu, J. L. and Zhang, L. Z., “Effects of wall thickness on the heat and moisture transfers in desiccant wheels for air dehumidification and enthalpy recovery”, Int. Com. in Heat Mass Trans., 29(2): 255-268, (2002). https://doi.org/10.1016/S0735-1933(02)00316-0
  7. Enteria, N., Yoshino, H., Satake, A., Mochida, A., Takaki, R., Yoshie, R., Mitamura, T. and Baba, S., “Experimental heat and mass transfer of the separated and coupled rotating desiccant wheel and heat wheel”, Exp. Ther. Fluid Sci., 34(5): 603-615, (2009). https://doi.org/10.1016/j.expthermflusci.2009.12.001 [17] Sparrow, E. M., Tong, J. C. K., Johnson, M. R. and Martin, G. P., “Heat and mass transfer characteristics of a regenerative total energy wheel”, Int. J. Heat Mass Trans., 50(7-8): 1631-1636, (2007). https://doi.org/10.1016/j.ijheatmasstransfer.2006.07.035
  8. Sheng, Y., Zhang, Y., Deng, N., Fang, L., Nie, J. and Ma, L., “Experimental analysis on performance of high temperature heat pump and desiccant wheel system”, Energy and Build., 66: 505-513, (2013). https://doi.org/10.1016/j.enbuild.2013.07.058
  9. Ruan, W., Qu, M. and Horton, W. T., “Modeling analysis of an enthalpy recovery wheel with purge air”, Int. J. Heat Mass Trans., 55(17-18): 4665-4672, (2012). https://doi.org/10.1016/j.ijheatmasstransfer.2012.04.025
  10. Zhang, L. Z. And Niu, J. L., “Performance comparisons of desiccant wheels for air dehumidification and enthalpy recovery”, App. Ther. Eng., 22(12): 1347-1367, (2002). https://doi.org/10.1016/S1359-4311(02)00050-9
  11. Zhang, L., Conjugate Heat and Mass Transfer in Heat Mass Exchanger Ducts (First Edition), Elsevier Inc., USA, ( 2014).
  12. ANSYS Inc. Fluent Theory Guide. 2013. Southpointe 275 Technology Drive Canonsburg USA: 621-647.
  13. Yıldırım, Z. E., “A Study on Isoterm Characteristics of Adsorbent-Adsorbate Pairs Used in Adsorption Heat Pumps.” MSc. Thesis, İzmir Technology Institute, İzmir, (2011).
  14. Ge, T. S., Li, Y., Wang, R. Z. and Dai Y. J., “A review of the mathematical models for predicting rotary desiccant wheels”, Renew. Sust. Energy Rev., 12(6): 1485-1528, (2008). https://doi.org/10.1016/j.rser.2007.01.012
  15. Lee, D. and Kim, D., “Analytical modelling of desiccant wheel”, Int. J. Refri., 42: 97-111, (2014). https://doi.org/10.1016/j.ijrefrig.2014.02.003
  16. Solmuş, İ., Dees, R. A. S., Yamalı, C. and Baker, D., “A two-energy equation model for dynamic heat and mass transfer in an adsorbent bed using silica gel/water pair”, Int. J. Heat Mass Trans.,55(19-20): 5275-5288, (2012). https://doi.org/10.1016/j.ijheatmasstransfer.2012.05.036
  17. Simonson, C. J. and Besant, R. W., “Energy wheel effectiveness: part i-development of dimensionless groups”, Int. J. Heat Mass Trans., 42(12): 2161-2170, (1998). https://doi.org/10.1016/S0017-9310(98)00325-1
  18. Simonson, C. J. and Besant, R. W., “Energy Wheel effectiveness: part ii-correlations.” Int. J. Heat Mass Trans., 42: 2171-2185, (1998). https://doi.org/10.1016/S0017-9310(98)00327-5
  19. Nobrega, C. E. L. and Brum, N. C. L., “Modeling and simulation of heat and enthalpy recovery wheels”, Energy, 34(12): 2063-2068, (2008). https://doi.org/10.1016/j.energy.2008.08.016
  20. Zhang, L. Z., Fu, H. X., Yang, Q. R. and Xu, J. C., “Performance comparisons of honeycomb-type adsorbent beds (wheels) for air dehumidification with various desiccant wall materials”, Energy, 65: 430-440, (2013). https://doi.org/10.1016/j.energy.2013.11.042
  21. Goldsworthy, M. J. and White, S., “Design and performance of an internal heat exchange desiccant wheel”, Int. J. Refri., 39: 152-159, (2013). https://doi.org/10.1016/j.ijrefrig.2013.10.009