SavedAdd your journal

Journals / Düzce Üniversitesi Orman Fakültesi Ormancılık Dergisi / 2018 / Cilt: 14 - Sayı: 1

Effect of Heat Treatment on Formaldehyde Emission in Particleboard

Hasan ÖZTÜRK
Aydın DEMİR
Gürsel ÇOLAKOĞLU
Pages
45–54
Publication Date
2018-07-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The formaldehyde emission rates in the heat-treated layers decreased with the time of treatment.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Heat treatment was applied without addition of chemicals harmful to human and environmental health, which are considered as an alternative to the impregnation process has many advantages and disadvantages for the wood based panel products.
📊
Key Findings & Data:In this study, the effects of heat treatment on the formaldehyde emission rate released on the surfaces of beech (Fagus orientalis Lipsky.) three-layer particleboard were investigated.
💡
Conclusion & Impact:The formaldehyde emission rates in the heat-treated layers decreased with the time of treatment.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Formaldehyde emission · Particleboard · Heat treatment

Özet

Heat treatment was applied without addition of chemicals harmful to human and environmental health, which are considered as an alternative to the impregnation process has many advantages and disadvantages for the wood based panel products. Formaldehyde has been linked to human health and environmental problems during and after manufacturing. Many studies are applied to reduce the formaldehyde emission. Because of the different applications of heat treatment, it has not been found in these studies. In this study, the effects of heat treatment on the formaldehyde emission rate released on the surfaces of beech (Fagus orientalis Lipsky.) three-layer particleboard were investigated. For this purpose, three groups were formed according to different time and temperature of heat treatment. After heat treatment, the lower, upper and middle layers of panels in the groups were separated then the formaldehyde emission rates from these layers were determined and compared with the control groups were not applied heat treatment. Consequently, the formaldehyde emission rates from the particleboard varied by layer (the lower, upper and middle) with heat treatment. The formaldehyde molecules in the upper layers treated at 150°C flowed from the hot side to the cold side. The formaldehyde emission rates in the heat-treated layers decreased with the time of treatment.

🔖

Cite This Article

ÖZTÜRK, H., DEMİR, A., ÇOLAKOĞLU, G. (2018). Effect of Heat Treatment on Formaldehyde Emission in Particleboard. Düzce Üniversitesi Orman Fakültesi Ormancılık Dergisi, Cilt: 14 - Sayı: 1, 45–54. https://ajindex.com/articles/118304

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (9)

  1. Aydin, I., Demirkir, C., Colak, S. and Colakoglu, G. 2010. Evaluation of flours of different wood barks as filler in plywood panels. III. National Karadeniz Forestry Congress, Artvin, 5: 1825-1833.
  2. Aydin, I., Colakoglu, G., Colak, S. and Demirkir, C. 2006. Effects of moisture content on formaldehyde emission and mechanical properties of plywood. Building and Environment, 41: 1311–1316.
  3. Brinkmann, E. 1978. Herstellung von Harnstoffharz-gebundenen Holzspanplatten mit niedrigem formaldehydgehalt auf ein-etagen-anlagen. Holz Roh-Werkstoff, 36: 296-298.
  4. Colak, S. 2002. The effects of impregnation procedure at plywood on technological properties, formaldehyde and acid emission of plywood. PhD Thesis, Karadeniz Technical University. Costa, N., Pereira, J., Ferra, J., Cruz, P., Martins, J., Magalhães, F., Mendes, A. and Carvalho, L. 2013. Scavengers for achieving zero formaldehyde emission on wood-based panels. Wood and Science Technology, 47:1261–1272. EN 322, 1993. Wood-based panels – Determination of moisture content, Brussels, Belgium. EN 717-3, 1996. Wood-based panels, determination of formaldehyde release, formaldehyde release by flask method. Brussels, Belgium. FAO 2016. FAOSTAT-FAO Statics Division - Production Quantity/Plywood. http://www.fao.org/faostat/en/#data/FO/visualize.
  5. Jiang, T., Gardner, D. J. and Baumann, M. G. D. 2002. Volatile organic compound emission arising from the hot-pressing of mixed-hardwood particleboard. Forest Products Journal, 52.11/12: 66. Kollman, F., Kuenzi, E. W. and Stam, A. S. 1975. Principles of wood science and technology. Springer Verlag. Berlin. New York. Marutzky, R. 1994. Release of formaldehyde by wood products. Forest Product Society, Report No: 94RS100R. Meyer, B., Johns, W. E. and Woo, J. K. 1980. Formaldehyde release from sulfur modified urea-formaldehyde resin systems. Forest Products Journal, 30(3): 24–31.
  6. Myers, G. E. 1984. How mole ratio of UF resin affects formaldehyde emission and other properties: literature critique. Forest Products Journal, 34(5): 35-41.
  7. Park, B. D., Chang, K. E. and Yong, P. J. 2006. Effects of formaldehyde to urea mole ratio on thermal curing behavior of urea–formaldehyde resin and properties of particleboard. Journal of Applied Polymer Science, 101(3): 1787-1792.
  8. Petersen, H. 1973. Zur formaldehyde absplatung bei der spanplattenerzeugung mit Harnstoff-formaldehyde-bindemitteln. Holz als Roh-und Werkstoff, 32(10): 402–10.
  9. Petinarakis, J. H. and Kavvouras, P. K. 2006. Technological factor