SavedAdd your journal

Journals / Celal Bayar Üniversitesi Fen Bilimleri Dergisi / 2021 / Cilt: 17 - Sayı: 1

Static Analysis of the Slotted Upper Plate of Low Pressure Casting Machine

Onur OZAYDİN
Yasemin Nur AYDIN
Ahmet Alper AKIŞ
Pages
35–41
Publication Date
2020-12-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It was concluded that the maximum stress on the mold is not at a level where it will cause failure.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the process improvement / Kaizen case study of a casting mold set-up process taking an average of 20 minutes, is examined.
📊
Key Findings & Data:As a result of this the set-up time decreased to an average of 9 minutes.
💡
Conclusion & Impact:It was concluded that the maximum stress on the mold is not at a level where it will cause failure.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:ANSYS Static Structural · ANSYS Topology Optimization · Case Study

Abstract

In this study, the process improvement / Kaizen case study of a casting mold set-up process taking an average of 20 minutes, is examined. The aim of this work is reducing the set-up time and improving ergonomic conditions. Since existing operating conditions cause a waste of time and result in non-ergonomic conditions, an air impact wrench had to be used in the mold assembly process. To be able to use the air impact wrench a new geometry had to implemented on casting mold and this design change was analyzed in ANSYS software to avoid a failure in working conditions. It was concluded that the maximum stress on the mold is not at a level where it will cause failure. After the initial geometry improvement process, a further ANSYS-Topology optimization process is conducted to reduce weight of the mold. As a result of this the set-up time decreased to an average of 9 minutes. Consequently, big benefits in terms of cycle time, occupational health and safety, improvement in the process and cost have been achieved.

🔖

Cite This Article

OZAYDİN, O., AYDIN, Y. N., AKIŞ, A. A. (2020). Static Analysis of the Slotted Upper Plate of Low Pressure Casting Machine. Celal Bayar Üniversitesi Fen Bilimleri Dergisi, Cilt: 17 - Sayı: 1, 35–41. https://ajindex.com/articles/116480

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Kabadayı, E. T. 2002. İşletmelerdeki Üretim Performans Ölçütlerinin Gelişimi, Özellikleri ve Sürekli İyileştirme ile İlişkisi. Doğuş Üniversitesi Dergisi; 61-75
  2. Joseph C. Chen, Y. L. 2010. From Value Stream Mapping Toward a Lean/sigma Continuous. International Journal of Production Research; 48: 1069–1086
  3. C-C Wang, K.-S. C.-H.-H. 2010. Application of 6-sigma Design System to Developing an Improvement Model for Multi-process Multi Characteristic. Vol. 225 Part B: J. Engineering Manufacture; 1205-1216
  4. Berger, A. 1997. Continuous improvement and kaizen: standardization and organizational designs. Integrated Manufacturing Systems; 110–117
  5. B. Modarress, A. A. 2005. Kaizen Costing for Lean Manufacturing: a Case Study. International Journal of Production Research; 43: 1751–1760
  6. K. Venkataramana, B. R. 2014. Application of Value Stream Mapping for Reduction of Cycle Time in a Machining Process. Procedia Materials Science; 6: 1187 – 1196
  7. Amit Kumar, A. a. 2013. Impacts of Kaizen in a Small-scale Industry of India: a Case Study. International Journal of Lean Six Sigma; 22-45
  8. Sunil Kumar, A. K. 2018. Process Improvement Through Lean-Kaizen Using Value Stream Map: A Case Study in India. The International Journal of Advanced Manufacturing Technology; 96: 2687–2698
  9. Aşkın Özdağoğlu, S. R. 2016. Applications of Kaizen and Cycle Time Reduction as Lean Production Techniques in a Semi-flexible PVC. Int. Journal of Management Economics and Business;12: 25-37
  10. ANSYS Topology Optimization. 2017. White paper, ANSYS Inc.,Canonsburg, PA U.S.A.; 1-4
  11. Dr.-Ing. Markus Stephan, D.-I. D.-P.-M. 2009. CFD Topology Optimization of Automotive Components. 4th European Automotive Simulation Conference EASC
  12. Chahande, R. Y. 1995. Automotive Applications of Topology Optimization. Structural Optimization; 9: 245-249
  13. Marco Cavazzuti, A. B. 2011. High performance automotive chassis design:. Struct Multidisc Optim; 44: 45–56
  14. Chao Li, I. Y. 2015. Conceptual and Detailed Design of an Automotive Engine Cradle by Using Topology, Shape, and Size Optimization. Structural and Multidisciplinary Optimization; 51: 547–564
  15. Hüseyin Güçlü YAVUZCAN, M. Ö. 2015. Yatık Ağız Açma Ve Kalibre Etme Makinasının Yapısal Analizi Ve Ağırlık Optimizasyonu. Gazi Üniversitesi Fen Bilimleri Dergisi; 3(3): 555-564
  16. R. Tavakoli, P. D. 2009. Optimal Riser Design in Sand Casting Process with Evolutionary Topology oOptimization. Struct Multidisc Optim; 205–214. 17.