Journals / Gıda / 2020 / Cilt: 45 - Sayı: 4

THE EFFECT OF GLYCEROL ON THE FORMATION OF CHITOSAN/POLYCAPROLACTONE AND CHITOSAN/CYCLOOLEFIN COPOLYMER BILAYER FILMS

GLİSEROLUN KİTOSAN BAZLI İKİ KATMANLI FİLMLER ÜZERİNE ETKİSİ

Journal
Gıda
Pages
763–773
Publication Date
2020-06-21
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The physicomechanical properties of CH films significantly influenced by the addition of glycerol and application of the second layer.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Chitosan (CH) films were prepared with/without glycerol as a plasticizer and coated with polycaprolactone (PCL) and cycloolefin copolymer (COC) to form bilayer films.
📊
Key Findings & Data:The contact angle of PCL film solutions was lower than COC film solutions (P <0.05).
💡
Conclusion & Impact:The physicomechanical properties of CH films significantly influenced by the addition of glycerol and application of the second layer.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Polikaprolakton · sikloolefin kopolimer · kitosan

Abstract

Chitosan (CH) films were prepared with/without glycerol as a plasticizer and coated with polycaprolactone (PCL) and cycloolefin copolymer (COC) to form bilayer films. The effect of the second layer coating on the physicomechanical properties of CH films was determined. The adhesion of PCL and COC solutions, when coated on CH film, was investigated by contact angle measurement. The contact angle of PCL film solutions was lower than COC film solutions (P <0.05). Scanning electron microscopy analysis revealed better compatibility between CH and PCL, while a phase separation was observed for CH/COC bilayers. Bilayers showed higher resistance to water when compared to neat CH film samples (P <0.05), while a reduction was found in tensile properties for bilayer films. Bilayer films had similar transmittance values with monolayer films (P >0.05). The physicomechanical properties of CH films significantly influenced by the addition of glycerol and application of the second layer.

Özet

Kitosan (CH) filmler, bir plastikleştirici olarak gliserol ile ve gliserolsüz hazırlanmış ve iki katmanlı filmler oluşturmak için polikaprolakton (PCL) ve sikloolefin kopolimer (COC) ile kaplanmıştır. İkinci bir katman olarak PCL ve COC uygulamasının CH filmlerinin fiziko-mekanik özellikleri üzerine etkileri belirlenmiştir. CH film üzerine kaplandığında PCL ve COC film çözeltilerinin yüzey adezyonu temas açısı ile araştırılmıştır. PCL film çözeltilerinin temas açısı COC film çözeltilerinden daha düşük bulunmuştur (P <0.05). Taramalı elektron mikroskopi analizi, CH ve PCL arasında daha iyi bir adezyon olduğunu gösterirken, CH/COC iki katmanlı filmlerde faz ayrımı gözlenmiştir. İki katmanlı filmler, CH filmlere oranla suya karşı daha yüksek direnç gösterirken (P <0.05), iki katmanlı filmlerin mekanik özelliklerinde bir azalma gözlenmiştir. İki katmanlı filmler, tek katmanlı filmler ile benzer optik özellikler göstermiştir (P >0.05). CH filmlerin fizikomekanik özellikleri, gliserol ilavesinden ve ikinci katmanın uygulanmasından önemli ölçüde etkilenmiştir.

🔖

Cite This Article

SÖĞÜT, E., SEYDİM, A. C. (2020). THE EFFECT OF GLYCEROL ON THE FORMATION OF CHITOSAN/POLYCAPROLACTONE AND CHITOSAN/CYCLOOLEFIN COPOLYMER BILAYER FILMS. Gıda, Cilt: 45 - Sayı: 4, 763–773. https://ajindex.com/articles/104536

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Arnon, H., Zaitsev, Y., Porat, R., Poverenov, E., Poverenov, E. (2014). Effects of carboxymethyl cellulose and chitosan bilayer edible coating on postharvest quality of citrus fruit. Postharvest Biol Tech, 87: 21–26.
  2. ASTM. (1995). Standard test methods for water vapor transmission of materials: E96/E96M-16. In Annual book of American Society for Testing and Materials Standards (Vol. 04.06, pp. 14). West Conshohocken, PA: ASTM. ASTM. (1999). Standard test method for specular gloss. Standard designation: D523. In annual book of American Society for Testing and Materials Standards, 06.01. Philadelphia: ASTM. ASTM. (2001). Standard test method for tensile properties of thin plastic sheeting: D882. In Annual book of American Society for Testing and Materials standards (Vol. 08.01, pp. 12). PA: ASTM. ASTM (2002). Standard test method for oxygen gas transmission rate through plastic film and sheeting using a coulometric sensor. Standard Designations: 3985-95. In Annual book of American Society for Testing and Materials Standards. Philadelphia, PA: ASTM. Avella, M., Errico, M. E., Laurienzo, P., Martuscelli, E., Raimo, M., Rimedio, R. (2000). Preparation and characterization of compatibilised polycaprolactone/starch composites. Polymer, 41: 3875–3881.
  3. Averous, L., Moro, L., Dole, P., & Fringant, C. (2000). Properties of thermoplastic blends: Starch polycaprolactone. Polymer, 41(11): 4157–4167.
  4. Bertuzzi, M.A., Armada, M., Gottifredi, J.C. (2007). Physicochemical characterization of starch-based films. J Food Eng, 82: 17–25.
  5. Bonilla, J., Atares, L., Vargas, M., Chiralt, A. (2013). Properties of wheat starch film-forming dispersions and films as affected by chitosan addition. J Food Eng, 114(3): 303–312.
  6. Bonilla, J., Fortunati, E., Atares, L, Chiralt, A., Kenny, J.M. (2014). Physical, structural and antimicrobial properties of poly vinyl alcohol-chitosan biodegradable films. Food Hydrocolloid, 35: 463-470.
  7. Bonilla, J., Vargas, M., Atares, L., Chiralt, A. (2011). Physical properties of chitosan-basil essential oil edible films as affected by oil content and homogenization conditions. Proc Food Sci, 1: 50-56.
  8. Bourtoom, T. Chinnan, M.S. (2008). Preparation and properties of rice starch–chitosan blend biodegradable film. LWT-Food Sci Technol, 41: 1633–1641.
  9. Farris, S., Introzzi, L., Biagioni, P., Holz, T., Schiraldi, A., Piergiovanni, L. (2011). Wetting of biopolymer coatings: Contact angle kinetics and image analysis investigation. Langmuir, 27: 7563–7574.
  10. Ferreira, A.R