KaydedilenlerDerginizi ekleyin

Dergiler / Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi / 2026 / Cilt: 32 Sayı: 6

Bazalt partikül takviyesinin üç boyutlu stereolitografi yöntemiyle üretilen polimerin mekanik özelliklerine etkisinin incelenmesi

Investigation of the effect of basalt particle reinforcement on the mechanical properties of polymer manufactured by three-dimensional stereolithography

Sercan Sabancı, Orhan Özcan Arıkan, Ege Ekmekçibaşı, Recep Tayyip Kırlangıç, Metin Yurddaşkal, Melis Yurddaşkal

Sayfa
1167–1175
Yayın Tarihi
2026-10-08
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗

Özet

Bu çalışmada, bazalt fiber partikül (BFP) takviyesinin üç boyutlu Stereolitografi (SLA) ile üretilmiş polimerin (Formlabs gri standart reçinesi) mekanik özelliklerine etkisi araştırılmıştır. Çalışmada, takviyesiz ve farklı oranlarda beşer adet (%0.5, %1 ve %2) BFP takviyeli numuneler üretilmiş ve her numuneye uygulanan çekme testleri, tokluk ölçümleri ve sertlik testleri ile mekanik özellikleri değerlendirilmiştir. Çekme testi sonuçları, %1 BFP ile takviyelendirilmiş numunelerin %45.8 artışla en yüksek çekme mukavemetini sergilediğini ortaya koymuştur. Buna karşılık, %0.5 takviye oranlı numunelerde ise çekme dayanımı referans (takviyelendirilmemiş) numunelere göre hafif bir artış (%4.3) göstermiştir. %2 BFP takviyeli numuneler ise en düşük çekme dayanımını göstermiştir. Tokluk testleri, %0.5 ve %1 BFP takviyesinde parçacıkların matriste nispeten iyi dağılmış olduğunu ve bu sebeple enerji absorplama kapasitesini olumlu yönde etkilediğini göstermiştir. Ancak %2 BFP takviyesinde parçacıkların aglomerasyonu ve homojen olmayan dağılımı, tokluğun azalmasına neden olmuştur. Sertlik testi sonuçları, takviye miktarının artmasıyla birlikte genel olarak numunelerin sertliğinin arttığını göstermiştir. Fakat %2 BFP takviyeli numuneler takviyesiz numunelere göre daha yüksek bir sertlik değerine sahip olmasına rağmen, %1 takviyeli numunelere göre daha düşük bir sertlik değeri göstermiştir. Arşimet yoğunluk testleri sonuçları, doluluk oranının %99 seviyesinde olduğunu ve doluluk miktarının mekanik özellikler üzerinde belirgin bir etkiye sahip olmadığını göstermiştir. Sonuç olarak, BFP takviyesi SLA ile üretilmiş polimerin mekanik özelliklerini önemli ölçüde iyileştirmiş olup özellikle, çekme dayanımını ve sertliğini belirgin bir şekilde arttırmıştır. Fakat, parçacıkların homojen dağılımı mekanik özelliklerin iyileştirilmesi için kritik önem taşımaktadır. Doluluk oranının yüksek olması ve iç boşlukların minimal düzeyde olması, SLA ile üretilen parçaların mekanik performansının güvenilir ve tutarlı olduğunu göstermektedir.

Abstract

In this study, the effect of basalt fiber particle (BFP) reinforcement on the mechanical properties of polymers produced by three-dimensional Stereolithography (SLA) was investigated. Five samples for unreinforced and reinforced different ratios of BFP (0.5%, 1%, and 2%) were manufactured, and their mechanical properties were evaluated through tensile tests, toughness calculations, and hardness tests. The tensile test results revealed that the samples reinforced with 1% BFP exhibited the highest tensile strength, with an increase of 45.8%. In contrast, samples with 0.5% reinforcement showed a slight increase in tensile strength (4.3%) compared to the reference (unreinforced) samples. Samples with 2% BFP reinforcement demonstrated the lowest tensile strength. Toughness tests indicated that at 0.5% and 1% BFP reinforcement, the particles were relatively well-dispersed in the matrix and therefore positively affected the energy absorption capacity. However, at 2% BFP reinforcement, particle agglomeration and inhomogeneous distribution led to a reduction in toughness. Hardness test results showed that the hardness of the samples generally increased with the reinforcement amount. Interestingly, although samples with 2% BFP reinforcement had higher hardness values than unreinforced samples, they exhibited lower hardness compared to samples with 1% reinforcement. The results of Archimedes density tests showed a fill rate of 99%, suggesting that the fill amount did not have a significant impact on mechanical properties. In conclusion, BFP reinforcement significantly improved the mechanical properties of polymers produced by SLA, particularly enhancing tensile strength and hardness. However, the homogeneous distribution of particles is critical for improving mechanical properties. The high fill rate and minimal internal voids demonstrate the reliability and consistency of the mechanical performance of SLA-produced parts.

Anahtar kelimeler
🔖

Bu Makaleye Atıf Yap

Sabancı, S., Arıkan, O. Ö., Ekmekçibaşı, E., Kırlangıç, R. T., Yurddaşkal, M., Yurddaşkal, M. (2026). Bazalt partikül takviyesinin üç boyutlu stereolitografi yöntemiyle üretilen polimerin mekanik özelliklerine etkisinin incelenmesi. Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 32 Sayı: 6, 1167–1175. https://doi.org/10.65206/pajes.70595

📄 Tam Metin PDF Okuyucu

↗Yeni Sekme

PDF belgesi yükleniyor...

Kaynakça (28)

  1. [1] Selim S, Şen Doğan R, Doğan M. "Analysis of the factors affecting firms’ Industry4.0readiness levels". Pamukkale University Journal of Engineering Sciences, 28(4), 613–624, 2022.
  2. [2] Demir S. "The effect of printing parameters on hardness in the production of Poli lactic acid (PLA)-based samples with a 3D printer". Pamukkale University Journal of Engineering Sciences, 30(2), 136–144, 2024.
  3. [3] Groover MP. Fundamentals of Modern Manufacturing: Materials, Processes, and Systems. 7th ed. New York, USA, John Wiley & Sons, 2020.
  4. [4] Taft RM, Kondor S, Grant GT. "Accuracy of rapid prototype models for head and neck reconstruction". Journal of Prosthetic Dentistry, 106(6), 399–408, 2011.
  5. [5] Kovalenko I, Garan M, Shynkarenko A, Zelený P, Šafka J. “Examining the relationship between forces during stereolithography 3D printing and geometric parameters of the model”. International Conference on Mechanical Engineering and Electrical Systems (ICMES), Singapore, Singapore, 16–18 December 2015.
  6. [6] Wiedemann B, Dusel KH, Eschl J. "Investigation into the influence of material and process on part distortion". Rapid Prototyping Journal, 1(3), 17–22, 1995.
  7. [7] Sun C, Zhang X. "The influences of the material properties on ceramic micro-stereolithography". Sensors and Actuators A: Physical, 101(3), 364–370, 2002.
  8. [8] Lian Q, Yang F, Xin H, Li D. "Oxygen-controlled bottom-up mask-projection stereolithography for ceramic 3D printing". Ceramics International, 43(17), 14956–14961, 2017.
  9. [9] Liu K, Zhang K, Bourell DL, Chen F, Sun H, Shi Y, Wang J, He M, Chen J. "Gelcasting of zirconia-based all-ceramic teeth combined with stereolithography". Ceramics International, 44(17), 21556–21563, 2018.
  10. [10] Wu H, Liu W, He R, Wu Z, Jiang Q, Song X, Chen Y, Cheng L, Wu S. "Fabrication of dense zirconia-toughened alumina ceramics through a stereolithography-based additive manufacturing". Ceramics International, 43(1), 968–972, 2017.
  11. [11] Bartolo PJ, Gaspar J. "Metal filled resin for stereolithography metal part". CIRP Annals-Manufacturing Technology, 57(1), 235–238, 2008.
  12. [12] Sano Y, Matsuzaki R, Ueda M, Todoroki A, Hirano Y. "3D printing of discontinuous and continuous fibre composites using stereolithography". Additive Manufacturing, 24, 521–527, 2018.
  13. [13] Goh GD, Yap YL, Agarwala S, Yeong WY. "Recent progress in additive manufacturing of fiber reinforced polymer composite". Advanced Materials Technologies, 4(1), 1800271, 2019.
  14. [14] Dong W, Ma H, Liu R, Liu T, Li S, Bao C, Song S. "Fabrication by stereolithography of fiber-reinforced fused silica composites with reduced crack and improved mechanical properties". Ceramics International, 47(17), 24121–24129, 2021.
  15. [15] Yunus DE, He R, Shi W, Kaya O, Liu Y. "Short fiber reinforced 3d printed ceramic composite with shear induced alignment". Ceramics International, 43(15), 11766–11772, 2017.
  16. [16] Lu Y, Han XX, Gleadall A, Zhao LG. "Fracture toughness of three-dimensional stereolithography printed polymer reinforced with continuous carbon fibers". 3D Printing and Additive Manufacturing, 9(4), 278–287, 2022.
  17. [17] Raajeshkrishna CR, Pradeep AS, Rishi Kumar RD. "Influence of fiber content on mechanical, tribological properties of short basalt fiber-reinforced nylon 6 and polypropylene composites". Journal of Thermoplastic Composite Materials, 34(6), 765-779, 2021.
  18. [18] Eselini N, Tirkes S, Akar AO, Tayfun U. "Production and characterization of poly (lactic acid)-based biocomposites filled with basalt fiber and flax fiber hybrid". Journal of Elastomers and Plastics, 52(8), 701-716, 2020.
  19. [19] Barczewski M, Mysiukiewicz O, Lewandowski K, Nowak D, Matykiewicz D, Andrzejewski J, Skórczewska K, Piasecki A. "Effect of basalt powder surface treatments on mechanical and processing properties of polylactide-based composites". Materials, 13(23), 5436, 2020.
  20. [20] Fiore V, Scalici T, Di Bella G, Valenza A. "A review on basalt fibre and its composites". Composites Part B: Engineering, 74, 74–94, 2015.
  21. [21] Sim J, Park C, Moon DY. "Characteristics of basalt fiber as a strengthening material for concrete structures". Composites Part B: Engineering, 36(6–7), 504–512, 2005.
  22. [22] Czigány T. "Basalt Fiber Reinforced Hybrid Polymer Composites". Materials Science Forum, 473–474, 59–66, 2005.
  23. [23] Mahesh Babu S, Venkateswara Rao M. "Effect of basalt powder on mechanical properties and dynamic mechanical thermal analysis of hybrid epoxy composites reinforced with glass fiber". Journal of the Chinese Advanced Materials Society, 6(3), 311–328, 2018.
  24. [24] Chai R, Zhu W, Li Q, Zou H, Han Y, Zhao Y, Ran X. "Effect of Basalt Fiber Content on Mechanical and Tribological Properties of Copper-Matrix Composites". Metals, 12(11), 1925, 2022.
  25. [25] Matykiewicz D, Barczewski M, Knapski D, Skórczewska K. "Hybrid effects of basalt fibers and basalt powder on thermomechanical properties of epoxy composites". Composites Part B: Engineering, 125, 157–164, 2017.
  26. [26] Zhou Y, Fan M, Chen L. "Interface and bonding mechanisms of plant fibre composites: An overview". Composites Part B: Engineering, 101, 31-45, 2016.
  27. [27] Matykiewicz D, Barczewski M, Michałowski S. "Basalt powder as an eco-friendly filler for epoxy composites: Thermal and thermo-mechanical properties assessment". Composites Part B: Engineering, 164, 272–279, 2019.
  28. [28] Subramanian LS, Palanisamy S, Karuppusamy M, Azeez A, Kashif Ali S, Kalathil S, Abbas M, Alfarraj SA, Ali Alharbi S. "Eco-friendly hybrid epoxy composites reinforced with snake grass fiber and dual agro-waste fillers for enhanced mechanical and acoustic performance" BioResources 21(2), 3636–3649, 2026.